DS1856E-030+ Maxim Integrated Products, DS1856E-030+ Datasheet - Page 22
![IC RES TEMP-CNTRL 30/10K 16TSSOP](/photos/6/56/65666/175-16-tssop_sml.jpg)
DS1856E-030+
Manufacturer Part Number
DS1856E-030+
Description
IC RES TEMP-CNTRL 30/10K 16TSSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1856B-050.pdf
(31 pages)
Specifications of DS1856E-030+
Taps
256
Resistance (ohms)
10K, 30K
Number Of Circuits
2
Temperature Coefficient
50 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.85 V ~ 5.5 V
Operating Temperature
-40°C ~ 95°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP
Resistance In Ohms
10K, 30K
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Dual, Temperature-Controlled Resistors with Inter-
nally Calibrated Monitors and Password Protection
22
Table Select
Config
____________________________________________________________________
0
Reserved .................... <R-NA><W-all><00h>
PWE........................... <R-NA><W-all><FFFFFFFFh> Password Entry. There are two
TBL Sel...................... <R-all/W-all><00h> Table Select. The upper memory tables of the
Mode.......................... <R-pw2/W-pw2><NV><03h>
a)
b) AEN ................... At Power-On this bit is HIGH, which enables autocontrol of the LUT.
T Index....................... <R-pw2><W-pw2+AENb><00h> Holds the calculated index based on
d) V
e)
f)
g) MON2 Hi........... High Warning Status for MON2 measurement.
h) MON2 Lo .......... Low Warning Status for MON2 measurement.
Warning
a)
b) MON3 Lo........... Low Warning Status for MON3 measurement.
TEN.................... At Power-On this bit is HIGH, which enables autocontrol of the LUT.
MON1 Hi........... High Warning Status for MON1 measurement.
MON1 Lo .......... Low Warning Status for MON1 measurement.
MON3 HI........... High Warning Status for MON3 measurement.
CC
1
Lo .............. Low Warning Status for V
................... <R-all><W-NA><00h> Low warning Status bits.
passwords for the DS1856. The lower level password (PW1) has
all the access of a normal user plus those made available with PW1.
The higher level password (PW2) has all of the access of PW1
plus those made available with PW2. The value of the password reside
in EE inside of PW2 memory.
DS1856 are accessible by writing the correct table value in this register.
If the device is configured to have a Table 01h then writing a 00h or a
01h in this byte will access that table.
If this bit is written to a ZERO then the resistor values are writeable by
the user and the LUT recalls are disabled. This allows the user to
interactively test their modules by manually writing resistor values. The
resistors will update with the new value at the end of the write cycle.
Thus both registers (Res0 and Res1) should be written in the same
write cycle. The 2-wire Stop condition is the end of the write cycle.
If this bit is cleared to a ZERO then the temperature calculated index
value ( T index ) is writeable by the user and the updates of calculated
indexes are disabled. This allows the user to interactively test their
modules by controlling the indexing for the look-up tables. The recalled
values from the LUTs will appear in the resistor registers after the next
completion of a temperature conversion (just like it would happen in
auto mode). Both pots will update at the same time (just like it would
happen in auto mode).
the Temperature Measurement. This index is used for the address
during Look-up of Tables 4 and 5.
supply is below the POA trip point value. It clears itself when a V
measurement is completed and the value is above the low threshold.
Register Descriptions (continued)
CC
measurement. This bit is set when the V
CC
.
CC