AS1507-BTDT-100 austriamicrosystems, AS1507-BTDT-100 Datasheet
AS1507-BTDT-100
Specifications of AS1507-BTDT-100
Related parts for AS1507-BTDT-100
AS1507-BTDT-100 Summary of contents
Page 1
... Datasheet General Description The AS1507 is a linear, dual 256-tap digital potentiome- ter specifically designed to replace discrete/mechanical potentiometers and is ideal for applications requiring a low-temperature-coefficient variable resistor. The device is controlled via a 3-wire SPI-compatible interface and features an internal EEPROM for storing wiper positions. Several device variants are available differentiated by ...
Page 2
... EEPROM is not affected. Active-High signal. Internal pull-down resistor. Can be left 16 MUTE unconnected if not used. Exposed Pad The exposed pad is not internally connected. Connect to GND or leave floating. N/A www.austriamicrosystems.com/Digital-Potentiometers/AS1507 VDD 1 12 HIGH B SCLK 2 11 WIPER B AS1507 10 LOW B SDIO 3 CSN 4 9 READY Description Revision 1. ...
Page 3
... The maximum rating voltage must not be exceeded during Latch-up test of the device. www.austriamicrosystems.com/Digital-Potentiometers/AS1507 may cause permanent damage to the device. These are stress ratings only, Min Max Units -0.3 +7 -0.3 V 0.3 AS1507-10 +1 AS1507- -100 100 mA 48 ºC/W -40 +85 ºC -60 +150 ºC +150 º ...
Page 4
... AMB Condition Digital Inputs = V or GND AMB Includes Non-Volatile Write to Memory AS1507-10 AS1507-50 & -100 AS1507-10 2 AS1507-50 & -100 +85ºC AMB AS1507-10 AS1507-50 AS1507-100 AS1507-10 AS1507-50 AS1507-100 AS1507-10 AS1507-50 & -100 @ 3V AS1507-50 & -100 @ 5V AS1507-10 AS1507-50 & -100 AS1507-10 AS1507-50 AS1507-100 ...
Page 5
... This parameter is not tested but ensured by characterization. Note: All limits are guaranteed. The parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality Control) methods. www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Condition Min AS1507-10 AS1507-50 AS1507-100 AS1507-10 AS1507-50 AS1507-100 T = +85ºC AMB T = +25ºC AMB T = +85º ...
Page 6
... SCLK-Rise to CSN-Fall Delay CS0 t CSN-Rise to SCLK-Rise Hold CS1 t CSN Pulse-Width High CSW t Write Non-Volatile Register Busy Time BUSY www.austriamicrosystems.com/Digital-Potentiometers/AS1507 = -40 to +85ºC. Typ values are at V AMB 10. Digital timing data is guaranteed by design and characteriza- Condition Revision 1.01 = +5.0V +25ºC DD AMB Min Typ ...
Page 7
... Figure 7. DNL vs. TAP Position 100kΩ, Divider Mode 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0 128 160 192 224 256 Tap Position www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Figure 4. INL vs. TAP Position 10kΩ, Divider Mode 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0 128 160 192 224 256 Tap Position Figure 6. INL vs. TAP Position 50kΩ ...
Page 8
... Figure 13. DNL vs. TAP Position 100kΩ,Varistor Mode 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0 128 160 192 224 256 Tap Position www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Figure 10. INL vs. TAP Position 10kΩ, Varistor Mode 2 1.6 1.2 0.8 0.4 0 -0.4 -0.8 -1.2 -1 128 160 192 224 256 Tap Position Figure 12. INL vs. TAP Position 50kΩ ...
Page 9
... Tap Position Figure 17. DAC Resistor vs. Temperature 118 117 116 115 114 113 112 111 110 Temperature (°C) Figure 19. EEPROM Data Retention vs. Temperature 10000 1000 100 Temperature (°C) www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Figure 16. Wiper Resistance vs. TAP; 3V 180 160 140 120 100 Figure 18. Gain vs. Bandwidth - 105 125 Revision 1 ...
Page 10
... Note: Integrated power-on reset circuitry loads the wiper position from the EEPROM at power-up. Digital Interface The AS1507 uses an SPI-compatible 3-wire interface for command settings of the device consisting of two input sig- nals (chip-select - CSN, and data clock - SCLK) and one bi-directional data pin (SDIO). Driving CSN low enables serial interface and the command/data are passed into the device synchronously by each SCLK rising edge ...
Page 11
... Power-Up The AS1507 contains an integrated power-up circuit. At power up, the data are transferred from the non-volatile mem- ory to the wiper register. The wiper register moves to the stored position. This data transfer takes 5µs after the supply has reached the POR trigger level. ...
Page 12
... With the next falling edge of CSN the SDIO pin is set to an input pin again. Read Wiper Register The AS1507 features the capability to read the data from the wiper register via the SPI interface page 13). This command can be implemented 16-bit command. The SDIO pin is a bi-directional pin. During the CSN low phase of the sequence, the SDIO pin is used as input pin to set the command byte ...
Page 13
... AS1507 Datasheet - Figure 21. 8-Bit Command Word CSN SCLK SDIO C7 C6 Figure 22. 16-Bit Command/Data Word CSN SCLK SDIO Figure 23. 16-Bit Read Command CSN SCLK SDIO Figure 24. 16-Bit EEPROM Write Command CSN SCLK SDIO READY www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Revision 1. tBUSY ...
Page 14
... IN WIPERA Offset Voltage and Gain Adjustment Connect one potentiometer of the AS1507 amp to nullify the offset voltage over the operating temperature range. Use the second potentiometer in the feedback path to adjust the gain of the op amp Figure 26. Offset Voltage and Gain Adjustment Circuit HIGHA ...
Page 15
... Adjustable Voltage Reference Figure 29 shows the device used as the feedback resistor in an adjustable voltage-reference application. Output volt- ages of external voltage references, supervisory reset thresholds, or LED brightness control can be independently adjusted by changing the wiper position of the AS1507. Figure 29. Adjustable Voltage Reference Circuit – ...
Page 16
... Dimension b applies to metallized terminal and is measured between 0.15 and 0.30mm from terminal tip refers to the maximum number of terminals on D side. 6. Unilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals. www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Symbol Max Notes D BSC 0 ...
Page 17
... Potentiometer with SPI Interface AS1507-BTDT-50 and High Endurance EEPROM ASPD Potentiometer with SPI Interface AS1507-BTDT-100 and High Endurance EEPROM Note: All products are RoHS compliant. Buy our products or get free samples online at ICdirect: Technical Support is found at For further information and requests, please contact us or find your local distributor at www ...
Page 18
... No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com/Digital-Potentiometers/AS1507 Revision 1. ...