AD5243BRMZ100 Analog Devices Inc, AD5243BRMZ100 Datasheet - Page 17

• Manufacturer Part Number: AD5243BRMZ100
• Description: IC DGTL POT DUAL 100K I2C 10MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5243BRMZ100

• Temperature Coefficient: 35 ppm/°C Typical
• Taps: 256
• Resistance (ohms): 100K
• Number Of Circuits: 2
• Memory Type: Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Resistance In Ohms: 100K
• End To End Resistance: 100kohm
• No. Of Steps: 256
• Resistance Tolerance: ± 20%
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: Serial, I2C, 2-Wire
• No. Of Pots: Dual
• Number Of Elements: 2
• # Of Taps: 256
• Resistance (max): 100KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (2-Wire/I2C)
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 10
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD5243EVAL - BOARD EVAL FOR AD5243
• Lead Free Status / Rohs Status: Compliant

Write Mode
Table 9. AD5243 Write Mode
S
Table 10. AD5248 Write Mode
S
Read Mode
Table 11. AD5243 Read Mode
S
Table 12. AD5248 Read Mode
S
Table 13. SDA Bits Descriptions
Bit
S
P
A
AD0, AD1
X
W
R
A0
SD
T
OW
D7, D6, D5, D4, D3, D2, D1, D0
0
0
0
0
1
1
1
Slave address byte
0
1
0
Slave address byte
1
1
0
0
1
Slave address byte
1
1
Slave address byte
AD1
1
1
1
1
1
AD0
W
AD1
1
W
Description
Start condition.
Stop condition.
Acknowledge.
Package pin-programmable address bits.
Don’t care.
Write.
Read.
RDAC subaddress select bit.
Shutdown connects wiper to B terminal and open circuits the A terminal. It does not change the
contents of the wiper register.
OTP programming bit. Logic 1 programs the wiper permanently.
Overwrites the fuse setting and programs the digital potentiometer to a different setting. Upon
power-up, the digital potentiometer is preset to either midscale or fuse setting, depending on
whether the fuse link was blown.
Data bits.
A
1
A
A0
AD0
A0
R
SD
SD
Instruction byte
R
X
A
Instruction byte
X
X
A
Rev. A | Page 17 of 20
D7
X
X
D7
X
X
D6
X
X
D6
X
X
D5
X
A
D5
A
D7
D4
D7
Data byte
D4
D6
Data byte
D6
D3
D5
D3
D5
D4
D2
Data byte
Data byte
D4
D2
D3
D3
D1
AD5243/AD5248
D1
D2
D2
D0
D1
D0
D1
D0
D0
A
A
A
A
P
P
P
P