MCP4662-103E/UN Microchip Technology, MCP4662-103E/UN Datasheet - Page 60
![IC DGTL POT 10K 256TAPS 10-MSOP](/photos/6/59/65940/c04-021-msop_sml.jpg)
MCP4662-103E/UN
Manufacturer Part Number
MCP4662-103E/UN
Description
IC DGTL POT 10K 256TAPS 10-MSOP
Manufacturer
Microchip Technology
Datasheet
1.MCP4541T-502EMF.pdf
(92 pages)
Specifications of MCP4662-103E/UN
Taps
257
Resistance (ohms)
10K
Number Of Circuits
2
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Resistance In Ohms
10K
End To End Resistance
100kohm
Track Taper
Linear
Resistance Tolerance
± 20%
No. Of Steps
256
Supply Voltage Range
2.7V To 5.5V
Control Interface
I2C, Serial
No. Of Pots
Dual
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4662-103E/UN
Manufacturer:
Microchip
Quantity:
229
MCP454X/456X/464X/466X
7.5
The Read Command can be issued to both the Volatile
and Non-Volatile memory locations. The format of the
command, see
I
MCP4XXX Command Byte, A bit, followed by a
Repeated Start bit, I
“1”), and the MCP4XXX transmitting the requested
Data High Byte, and A bit, the Data Low Byte, the Mas-
ter generating the A, and Stop condition.
The I
logic one (R/W = 1) to generate a read sequence. The
memory location read will be the last address
contained in a valid write MCP4XXX Command Byte or
address 00h if no write operations have occurred since
the device was reset (Power-on Reset or Brown-out
Reset).
During a write cycle (Write or High Voltage Write to a
Non-Volatile memory location) the Read command can
only read the Volatile memory locations. By reading the
Status Register (04h), the Host Controller can
determine when the write cycle has completed (via the
state of the EEWA bit).
Read operations initially include the same address byte
sequence as the write sequence (shown in
This sequence is followed by another control byte
(including the Start condition and Ackowledge) with the
R/W bit equal to a logic one (R/W = 1) to indicate a
read. The MCP4XXX will then transmit the data con-
tained in the addressed register. This is followed by the
master generating an A bit in preparation for more data,
or an A bit followed by a Stop. The sequence is ended
with the master generating a Stop or Restart condition.
The internal address pointer is maintained. If this
address pointer is for a non-volatile memory address
and the read control byte addresses the device during
a Non-Volatile Write Cycle (t
with an A bit.
7.5.1
Figure 7-4
For single reads the master sends a STOP or
RESTART condition after the data byte is sent from the
slave.
7.5.1.1
Figure 7-5
Refer to
sequence.
DS22107A-page 60
2
C Control Byte (with R/W bit set to “0”), A bit,
2
C Control Byte requires the R/W bit equal to a
Read Data
Normal and High Voltage
show the waveforms for a single read.
shows the sequence for a Random Reads.
Figure 7-5
SINGLE READ
Random Read
Figure
2
C Control Byte (with R/W bit set to
7-4, includes the Start condition,
for the random byte read
WC
) the device will respond
Figure
6-9).
7.5.2
Continuous reads allows the devices memory to be
read quickly. Continuous reads are possible to all mem-
ory locations. If a non-volatile memory write cycle is
occurring, then Read commands may only access the
volatile memory locations.
Figure 7-6
reads.
For continuous reads, instead of transmitting a Stop
or Restart condition after the data transfer, the master
reads the next data byte. The sequence ends with the
master Not Acknowledging and then sending a Stop or
Restart.
7.5.3
The High Voltage Command (HVC) signal is
multiplexed with Address 0 (A0) and is used to indicate
that the command, or sequence of commands, are in
the High Voltage mode. High Voltage commands allow
the device’s WiperLock Technology and write protect
features to be enabled and disabled.
The HVC pin has an internal resistor connection to the
MCP4XXXs internal V
7.5.4
The MCP4XXX expects to receive entire, valid I
commands and will assume any command not defined
as a valid command is due to a bus corruption and will
enter a passive high condition on the SDA signal. All
signals will be ignored until the next valid Start
condition and Control Byte are received.
IGNORING AN I
“FALLING OFF” THE BUS
shows the sequence for three continuous
CONTINUOUS READS
THE HIGH VOLTAGE COMMAND
(HVC) SIGNAL
DD
© 2008 Microchip Technology Inc.
signal.
2
C TRANSMISSION AND
2
C