MCP4562-103E/MS Microchip Technology, MCP4562-103E/MS Datasheet - Page 11

• Manufacturer Part Number: MCP4562-103E/MS
• Description: IC DGTL POT 10K 256TAPS 8-MSOP
• Manufacturer: Microchip Technology

Specifications of MCP4562-103E/MS

• Taps: 257
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Temperature Coefficient: 150 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Resistance In Ohms: 10K
• End To End Resistance: 100kohm
• Track Taper: Linear
• Resistance Tolerance: ± 20%
• No. Of Steps: 256
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: I2C, Serial
• No. Of Pots: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AC/DC CHARACTERISTICS (CONTINUED)
© 2008 Microchip Technology Inc.
DC Characteristics
Digital Inputs/Outputs (SDA, SCK, HVC/A0, A1, A2, WP)
Schmitt Trigger
High Input
Threshold
Schmitt Trigger
Low Input
Threshold
Hysteresis of
Schmitt Trigger
Inputs (Note 6)
High Voltage Input
Entry Voltage
High Voltage Input
Exit Voltage
High Voltage Limit
Note 1:
Parameters
2:
3:
4:
5:
6:
7:
8:
9:
10: Supply current is independent of current through the resistor network
11: When HVC/A0 = V
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
MCP4XX1 only.
MCP4XX2 only, includes V
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design.
Non-linearity is affected by wiper resistance (R
temperature.
The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and
then tested.
POR/BOR is not rate dependent.
V
V
V
V
Sym
IHHEN
IHHEX
V
V
MAX
HYS
IH
IL
IHH
, the I
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
All parameters apply across the specified operating ranges unless noted.
V
Typical specifications represent values for V
0.45 V
0.05 V
0.5 V
0.7 V
0.7 V
0.7 V
0.7 V
0.1 V
0.1 V
0.1 V
DD
WZSE
DD
N.A.
N.A.
Min
-0.5
-0.5
-0.5
-0.5
8.5
—
—
—
—
= +2.7V to 5.5V, 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ devices.
current is less due to current into the HVC/A0 pin. See I
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
W
and V
with V
0.1V
MCP454X/456X/464X/466X
WFSE
Typ
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
A
DD
= V
.
DD
W
0.8V
0.2V
0.3V
0.3V
0.3V
0.3V
12.5
12.5
V
V
V
V
V
), which changes significantly overvoltage and
Max
DD
and V
—
—
MAX
MAX
MAX
MAX
—
—
—
—
—
—
—
DD
DD
DD
DD
DD
(6)
(6)
(6)
+
B
–40°C ≤ T
= V
Units
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
SS
.
A
All inputs except SDA and SCL
All inputs except SDA and SCL
Threshold for WiperLock™ Technology
Pin can tolerate V
≤ +125°C (extended)
except
Inputs
SDA
SCL
SDA
SCL
SDA
SCL
SDA
SCL
and
and
and
and
All
DD
= 5.5V, T
2.7V ≤ V
(Allows 2.7V Digital V
5V Analog V
1.8V ≤ V
100 kHz
400 kHz
1.7 MHz
3.4 Mhz
100 kHz
400 kHz
1.7 MHz
3.4 Mhz
100 kHz
400 kHz
1.7 MHz
3.4 Mhz
Conditions
A
= +25°C.
DD
DD
MAX
V
V
V
V
PU
DD
DD
DD
DD
≤ 5.5V
≤ 2.7V
DD
DS22107A-page 11
or less.
specification
< 2.0V
≥ 2.0V
< 2.0V
≥ 2.0V
)
DD
with