DS1804-050+ Maxim Integrated Products, DS1804-050+ Datasheet - Page 6

• Manufacturer Part Number: DS1804-050+
• Description: IC POT TRIMMER NV 50K 8-DIP
• Manufacturer: Maxim Integrated Products

Specifications of DS1804-050+

• Taps: 100
• Resistance (ohms): 50K
• Number Of Circuits: 1
• Temperature Coefficient: 750 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: Increment/Decrement
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Resistance In Ohms: 50K
• Number Of Pots: Single
• Taps Per Pot: 100
• Resistance: 50 KOhms
• Wiper Memory: Non Volatile
• Digital Interface: Up/Down
• Operating Supply Voltage: 2.7 V to 5.5 V
• Supply Current: 400 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Tolerance: 20 %
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NOTES:
1) All voltages are referenced to ground.
2) Valid for V
3) Resistor input voltages cannot go below ground or exceed V
4) Maximum current specifications are based on the clock rate of
5) Standby current levels apply when all inputs are driven to appropriate supply levels.
6) Wiper load time is specified as the time required for the DS1804 to load the wiper position with the
7) The DS1804 is available in three resistor values. These include the DS1804-010, 10kW; the DS1804-
8) Valid at 25°C only.
9) Absolute linearity is used to compare measured wiper voltage versus expected wiper voltage as
10) Relative linearity is used to determined the change in voltage between successive tap positions. The
11) -3dB cutoff frequency characteristics for the DS1804 depend on potentiometer total resistance.
12) Capacitance values apply at 25°C.
13) See Figure 2.
14) Power-up time is specified as the time required before the three-terminal control becomes active after
15) At V
16) The
17) Wiper Storage Time, t
represents the current required when changing the wiper position.
V
contents of nonvolatile memory once V
than 2.7V.
050, 50kW; and the DS1804-100, 100kW.
determined by wiper position. The DS1804 is specified to provide an absolute linearity of ±0.60 LSB.
DS1804 is specified to provide a relative linearity specification of ±0.25 LSB.
DS1804-010, 1MHz; DS1804-050, 200 kHz; and DS1804-100, 100 kHz.
a stable power supply level has been reached.
allows the DS1804 three-terminal port to become inactive without writing the EEPROM memory of
the part.
of a new wiper position. The maximum time required to accomplish this task is specified at 10ms.
CC
.
CC
INC
= 2.7V, V
low to
CC
= 5V only.
CS
IL
= 0.8V.
inactive is specified to be 50ns minimum. This is the transition condition which
WST
, is the time require for the DS1804 to write EEPROM memory for storage
CC
has reached a stable operating voltage equal to or greater
6 of 8
CC
by the amounts as shown in the table.
INC
input. This specification
CS
,
INC
, U/
D
=