X9268TS24 Intersil, X9268TS24 Datasheet - Page 5

• Manufacturer Part Number: X9268TS24
• Description: IC DCP DUAL 100K 256TP 24SOIC
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of X9268TS24

• Taps: 256
• Resistance (ohms): 100K
• Number Of Circuits: 2
• Temperature Coefficient: 300 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Resistance In Ohms: 100K
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

PIN DESCRIPTIONS
Bus Interface Pins
S
The SDA is a bidirectional serial data input/output pin
for a 2-Wire slave device and is used to transfer data
into and out of the device. It receives device address,
opcode, wiper register address and data sent from an
2-Wire master at the rising edge of the serial clock
SCL, and it shifts out data after each falling edge of
the serial clock SCL.
It is an open drain output and may be wire-ORed with
any number of open drain or open collector outputs.
An open drain output requires the use of a pull-up
resistor. For selecting typical values, refer to the
guidelines for calculating typical values on the bus
pull-up resistors graph.
S
This input is used by 2-Wire master to supply 2-Wire
serial clock to the X9268.
D
The address inputs are used to set the least significant
3 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
Address input in order to initiate communication with
the X9268. A maximum of 8 devices may occupy the
2-Wire serial bus.
Potentiometer Pins
R
The R
connections on a mechanical potentiometer. Since
there are 2 potentiometers, there are 2 sets of R
R
and so on.
ERIAL
ERIAL
EVICE
H
L
, R
such that R
L
H
D
C
A
and R
ATA
LOCK
DDRESS
I
H0
NPUT
L
(SCL)
pins are equivalent to the terminal
and R
(A3 - A0)
/O
UTPUT
L0
5
are the terminals of POT 0
(SDA)
H
and
X9268
R
The wiper pin are equivalent to the wiper terminal of a
mechanical
potentiometers, there are 2 sets of R
is the terminal of POT 0 and so on.
Bias Supply Pins
S
G
The V
pin is the system ground.
Analog Supply Voltages (V+ and V
These supplies are the analog voltage supplies for the
potentiometer. The V+ supply is tied to the wiper
switches while the V- supply is used to bias the
switches and the internal P+ substrate of the
integrated circuit. Both of these supplies set the
voltage limits of the potentiometer.
Other Pins
N
No connect pins should be left open. This pins are
used for Intersil manufacturing and testing purposes.
H
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
YSTEM
W
O
ARDWARE
ROUND
C
ONNECT
CC
S
(V
pin is the system supply voltage. The V
UPPLY
SS
W
potentiometer.
)
RITE
V
OLTAGE
P
ROTECT
(V
I
CC
Since
NPUT
)
AND
-
W
(WP)
)
there
such that R
S
UPPLY
August 29, 2006
are
FN8172.4
W0
SS
4