LM8300IMT9B/NOPB National Semiconductor, LM8300IMT9B/NOPB Datasheet - Page 8
![IC TOUCHSCREEN CTLR 48-TSSOP](/photos/6/59/65904/pkg_mtd48_sml.jpg)
LM8300IMT9B/NOPB
Manufacturer Part Number
LM8300IMT9B/NOPB
Description
IC TOUCHSCREEN CTLR 48-TSSOP
Manufacturer
National Semiconductor
Type
Resistiver
Datasheet
1.LM8500IMT9BNOPB.pdf
(20 pages)
Specifications of LM8300IMT9B/NOPB
Touch Panel Interface
4-Wire
Number Of Inputs/keys
1 TSC
Resolution (bits)
10 b
Data Interface
UART
Data Rate/sampling Rate (sps, Bps)
38.4k
Voltage - Supply
2.7 V ~ 5.5 V
Current - Supply
11.5mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
48-TSSOP
Voltage Supply Source
Single Supply
For Use With
LM8300-REF-01 - BOARD EVALUATION LM8300
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Sampling Rate (per Second)
-
Other names
LM8300IMT9B
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM8300IMT9B/NOPB
Manufacturer:
NS/TI
Quantity:
8
www.national.com
Input Capacitance
8.0 Electrical Characteristics
DC Electrical Characteristics (0˚C ≤ T
Resolution
DNL
DNL
INL
INL
Offset Error
Offset Error
Gain Error
Gain Error
Input Voltage Range
Analog Input Leakage Current
Analog Input Resistance (Note 8)
Analog Input Capacitance
Operating Current on AV
Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 4: Maximum rate of voltage change must be
Note 5: Supply and IDLE currents are measured with CKI driven with a
square wave Oscillator, CKO driven 180˚ out of phase with CKI, inputs
connected to V
A/D Converter Electrical Characteristics (0˚C ≤ T
mode only)
Note 8: Resistance between the device input and the internal sample and hold capacitance.
9.0 Functional Description
9.1 GENERAL
The LM8300/8500 is a 4-wire resistive touch screen control-
ler. The primary communication is through the built in UART
operating at a baud rate of 38400. The LM8300/8500 has the
ability to measure pressure on the Z-axis, in addition to the
X-Y coordinates.
The device has the capability to do a 2, 5, and 13 point
calibration. All calibration data is stored in the internal non-
volatile storage element. In addition, all settings pertaining to
the controller are stored internally. This feature negates the
need for external EEPROM.
The device has three built in averaging algorithms: oversam-
pling, delta, and focus. These algorithms help to minimize
noise and A/D variation due to noise. Refer to the averaging
algorithm section for a more detail explanation. These algo-
rithms are implemented on-chip, freeing the main processor
from these tasks. To further minimize noise in extremely
noisy environments, the device has the ability to route the
signal from the touch panel to an external filtering stage
before A/D conversions are performed.
To minimize power consumption, the device can be put into
power save mode. The device can be set to go into power
save mode automatically or manually by pulling the external
shutdown pin low.
Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
CC
and outputs driven low but not connected to a load.
Parameter
Parameter
CC
<
0.5 V/ms.
V
V
V
V
V
V
V
V
2.7V ≤ V
AV
CC
CC
CC
CC
CC
CC
CC
CC
CC
(Continued)
= 5V
= 3V
= 5V
= 3V
= 5V
= 3V
= 5V
= 3V
Conditions
= 5.5V
CC
<
Conditions
5.5V
A
8
≤ +70˚C)
Note 6: The HALT mode will stop CKI from oscillating. Measurement of I
HALT is done with device neither sourcing nor sinking current; all inputs tied
to V
Note 7: Absolute Maximum Ratings should not be exceeded.
9.2 ADVANCED PIN DESCRIPTIONS
CLK_SET — This pin is the selection pin used to determine
the operating frequency of the controller. On power up, the
controller polls this pin to determine if the operating fre-
quency is set to 10 MHz or 3.3 MHz. If the pin is left floating
or tied high, then the operating frequency is 10 MHz. If the
pin is tied low, then the operating frequency is set to 3.3
MHz.
Note: This is available on the LM8500 only.
SHUTDOWN — This is the external shut down pin. When
pulled low, the controller goes into power saving mode. This
selection pin state has higher priority than the internal power
save mode settings.
WAKE_UP — This pin is used to wake the controller from
power save mode. When the device is in power save mode,
the pin must be tied to one of X-Y lines coming from the
touch screen panel.
X+ — Connect to X+ terminal of the resistive screen.
X- — Connect to X- terminal of the resistive screen.
Y+ — Connect to Y+ terminal of the resistive screen.
Y- — Connect to Y- terminal of the resistive screen.
Filter_out — Analog output to external filter. The use of the
external filter is controlled by sending a command byte of
$A0 on the UART to the controller.
Filter_in — Analog input from external filter. The use of the
external filter is controlled by sending a command byte of
$A0 on the UART to the controller.
CC
; A/D converter and clock monitor and BOR disabled.
Min
0
(Continued)
A
≤ +70˚C) (Single-ended
Typ
0.2
Min
Typ
Max
±
±
±
±
V
0.5
0.6
10
±
±
±
±
6k
1.5
2.5
1.5
2.5
7
CC
1
1
2
4
Max
7
Units
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
Bits
mA
µA
pF
V
Ω
Units
pF
DD