MAX195BCWE+ Maxim Integrated Products, MAX195BCWE+ Datasheet - Page 18
![IC ADC 16BIT 85KSPS SHTDN 16SOIC](/photos/5/17/51709/175-16-soic_w__sml.jpg)
MAX195BCWE+
Manufacturer Part Number
MAX195BCWE+
Description
IC ADC 16BIT 85KSPS SHTDN 16SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX195BEWE.pdf
(28 pages)
Specifications of MAX195BCWE+
Number Of Bits
16
Sampling Rate (per Second)
85k
Data Interface
QSPI™, Serial, SPI™
Number Of Converters
2
Power Dissipation (max)
80mW
Voltage Supply Source
Analog and Digital, Dual ±
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.300", 7.50mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
An OR gate is used to synchronize the “start” signal to
the asynchronous CLK, as described in the External
Clock section. As with Mode 1, the QSPI processor must
run CLK during calibration and either count CLK cycles
or, as is done here, monitor EOC to determine when cal-
ibration is complete. Also, EOC is polled by the µP to
determine when a conversion result is available. When
EOC goes low, data is clocked out at the highest QSPI
data rate (4.19Mbps). After the data is transferred, a
new conversion can be initiated whenever desired.
The timing specification for SCLK-to-DOUT valid (t
imposes some constraints on the serial interface. At
SCLK rates up to 2.5Mbps, data is clocked out of the
MAX195 by a falling edge of SCLK and may be
clocked into the µP by the next rising edge (CPOL = 0,
CPHA = 0). For data rates greater than 2.5Mbps (or for
lower rates, if desired) it is necessary to clock data out
of the MAX195 on SCLK’s falling edge and to clock it
into the µP on SCLK’s next falling edge (CPOL = 0,
CPHA = 1). Also, your processor hold time must not
exceed t
maximum SCLK rates may not be possible with some
interface specifications that are subsets of SPI.
16-Bit, 85ksps ADC with 10µA Shutdown
Figure 20. Timing Diagram for Circuit of Figure 19 (Mode 2)
18
______________________________________________________________________________________
SD
START
DOUT
SCLK
* INTERRUPT LATENCY OF THE PROCESSOR
EOC
CLK
CS
minimum (20ns). As with CLK in mode 1,
588ns
1.3 s
CONVERSION TIME
9.4 s
SD
)
17 s*
For best system performance, use printed circuit
boards with separate analog and digital ground planes.
Wire-wrap boards are not recommended. The two
ground planes should be tied together at the low-
impedance power-supply source and at the MAX195
(Figure 22.) If the analog and digital supplies come
from the same source, isolate the digital supply from
the analog supply with a low-value resistor (10Ω).
Constraints on sequencing the four power supplies are
as follows.
• Apply VDDA before VDDD.
• Apply VSSA before VSSD.
• Apply AIN and REF after VDDA and VSSA are present.
• The power supplies should settle within the
MAX195’s power-on delay (minimum 500ns) or you
should recalibrate the converter (pulse RESET low)
before use.
B15
B14
B13
239ns
5.1 s
B3 B2
Supplies, Layout, Grounding
B1 B0
4.19MHz
4 s
and Bypassing