AD9288BSTZ-40 Analog Devices Inc, AD9288BSTZ-40 Datasheet - Page 16
![IC ADC 8BIT DUAL 40MSPS 48-LQFP](/photos/6/59/65923/505-48-lqfp_sml.jpg)
AD9288BSTZ-40
Manufacturer Part Number
AD9288BSTZ-40
Description
IC ADC 8BIT DUAL 40MSPS 48-LQFP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9288BSTZ-40.pdf
(24 pages)
Specifications of AD9288BSTZ-40
Data Interface
Parallel
Number Of Bits
8
Sampling Rate (per Second)
40M
Number Of Converters
2
Power Dissipation (max)
189mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-LQFP
Resolution (bits)
8bit
Sampling Rate
40MSPS
Input Channel Type
Differential
Supply Voltage Range - Analog
2.7V To 3.6V
Supply Voltage Range - Digital
2.7V To 3.6V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9288BSTZ-40
Manufacturer:
ADI
Quantity:
480
Company:
Part Number:
AD9288BSTZ-40
Manufacturer:
ADI
Quantity:
1 000
Company:
Part Number:
AD9288BSTZ-40
Manufacturer:
ADI
Quantity:
100
Company:
Part Number:
AD9288BSTZ-40
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9288BSTZ-40
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9288
EVALUATION BOARD
The AD9218/AD9288 customer evaluation board offers an easy
way to test the AD9218 or the AD9288. The compatible pinout
of the two parts facilitates the use of one PCB for testing either
part. The PCB requires power supplies, a clock source, and a
filtered analog source for most ADC testing required.
POWER CONNECTOR
Power is supplied to the board via a detachable 12-lead power
strip. The minimum 3 V supplies required to run the board are
V
path, ±5 V supplies are required.
ANALOG INPUTS
Each channel has an independent analog path that uses a
wideband transformer to drive the ADC differentially from a
single-ended sine source at the input SMAs. The transformer
paths can be bypassed to allow the use of a dc-coupled path by
using two AD8138 op amps with a simple board modification.
The analog input should be band-pass filtered to remove any
harmonics in the input signal and to minimize aliasing.
VOLTAGE REFERENCE
The AD9288 has an internal 1.25 V voltage reference; an
external reference for each channel can be used instead by
connecting two external voltage references at the power
connector and setting jumpers at E18 and E19. The evaluation
board is shipped configured for internal reference mode.
DD
, V
DL
, and V
DD
. To allow the use of the optional amplifier
Rev. C | Page 16 of 24
CLOCKING
Each channel can be clocked by a common clock input at SMA
input ENCODE A/B. The channels can also be clocked
independently by a simple board modification. The clock input
should be a low jitter sine source for maximum performance.
DATA OUTPUTS
The data outputs are latched on-board by two 10-bit latches and
drive an 8-pin connector which is compatible with the dual-
channel FIFO board available from Analog Devices. This board,
together with ADC analyzer software, can greatly simplify ADC
testing.
DATA FORMAT/GAIN
The DFS/Gain pin can be biased for desired operation at the DFS
jumper located at the S1, S2 jumpers.
TIMING
Timing on each channel can be controlled if needed on the
PCB. Clock signals at the latches or the data ready signals that
go to the output 80-pin connector can be inverted if required.
Jumpers also allow for biasing of Pins S1 and S2 for power-
down and timing alignment control.