5-6605853-8 TE Connectivity, 5-6605853-8 Datasheet - Page 2
![1X1 MAG45, 10/100 714P10,G/Y REAR LED](/photos/41/71/417125/pr1840734_sml.jpg)
5-6605853-8
Manufacturer Part Number
5-6605853-8
Description
1X1 MAG45, 10/100 714P10,G/Y REAR LED
Manufacturer
TE Connectivity
Specifications of 5-6605853-8
Product Type
Connector
Number Of Cores
5
Magnetics
Integrated Magnetics
Jack Type
RJ45
Signal Routing Type
NIC
Profile
Standard
Pcb Mounting Orientation
Side Entry (Right Angle)
Jack Configuration
1 x 1
Turns Ratio
1:1
Shielded
Yes
Emi Finger - Bottom
With
Termination Method
Solder
Port Configuration
Single
Emi Fingers -top And Sides
With
Latch Orientation
Inverted - Latch Up
Pcb Tail Length (mm [in])
2.92 [0.115]
Contact Termination Type
Through Hole
Preloaded
Yes
Connector Style
Jack
Status Indicator
LED
Decoupling Capacitor
2KV
Rear Pcb Ground Tab
Without
Signal Lead Quantity
8
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Left Led Color (position #1)
Green
Right Led Color (position #2)
Yellow
Operating Temperature (°c [°f])
0 – 70 [32 – 158]
Applies To
Printed Circuit Board
Environmental Conditions
Office / Premises
Application
10/100BASE-T Ethernet
3.4.
3.5.
3.6.
Examination of product.
Dry circuit resistance.
Open circuit inductance.
Random vibration, operational.
Random vibration, non-operational.
Rev D
●
Product Codes
Product Codes for this product family are H363, H364, H365 and H366
Performance and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per EIA-364.
Test Requirements and Procedures Summary
Test Description
Temperature:
•
•
Standard: 0 to 70° C |
Extended temperature varieties: -40 to 85° C
Meet requirements of product
drawing, and dimensional and
plating requirements of FCC Part
68, Subpart F, Connector
Specification per Figure
68.500(d)(2)(i) 8 Position Series
Modular Jack.
See Engineering Report 502-1129.
OCL 350 µH minimum.
No discontinuities of 1
microsecond
or longer duration.
See Note.
See Note.
R 30 milliohms maximum.
Figure 1 (continued)
MECHANICAL
ELECTRICAL
Requirement
Measure per drawing, inspect
plating thickness per x-ray
evaluation per EIA-364-48 Method
C.
EIA-364-23A.
Subject specimens to 100 mA
maximum and 20 mV maximum
open circuit voltage.
See Figure 3.
ANSI X3.263, ref IEEE 802.3.
Measure and record mutual
inductance of mated and mounted
specimens at 100 kHz, 100 mV, 8
mA DC bias, and 25° C.
EIA-364-28D,
Test Condition VIIA.
Subject specimens to 1.0 G rms
between 3-500 Hz. PSD of .003.
45 minutes in each of 3 mutually
perpendicular planes.
EIA-364-28D,
Test Condition VIIA.
Subject specimens to 1.0 G rms
between 3-500 Hz. PSD of .003.
45 minutes in each of 3 mutually
perpendicular planes.
Procedure
108-2100
2 of 6