LTC1605CN Linear Technology, LTC1605CN Datasheet
LTC1605CN
Specifications of LTC1605CN
Available stocks
Related parts for LTC1605CN
LTC1605CN Summary of contents
Page 1
... The ADC has a microprocessor compatible, 16-bit or two byte parallel output port. A convert start input and a data ready signal (BUSY) ease connections to FIFOs, DSPs and microprocessors. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. 10µF 0.1µF ...
Page 2
... PLASTIC SO WIDE = 125°C, θ 95°C/W (G) JMAX JA = 125°C, θ 130°C/W (N) JMAX JA = 125°C, θ 130°C/W (SW) JMAX JA ORDER PART NUMBER LTC1605CN LTC1605CSW LTC1605IG LTC1605IN LTC1605ISW http://www.linear.com/leadfree/ LTC1605A TYP MAX MIN TYP MAX 16 16 1.0 1.0 ±3 ±2 ± ...
Page 3
U U ANALOG INPUT ● The specifications are 25°C. (Note 5) A SYMBOL PARAMETER V Analog Input Range (Note Analog Input Capacitance IN R Analog Input Impedance DYNAMIC ACCURACY SYMBOL PARAMETER ...
Page 4
LTC1605 U U DIGITAL INPUTS AND DIGITAL OUTPUTS operating temperature range, otherwise specifications are at T SYMBOL PARAMETER V Low Level Output Voltage OL I Hi-Z Output Leakage D15 Hi-Z Output Capacitance D15 ...
Page 5
ELECTRICAL CHARACTERISTICS Note 8: Bipolar offset is the offset voltage measured from – 0.5 LSB when the output code flickers between 0000 0000 0000 0000 and 1111 1111 1111 1111. Note 9: Guaranteed by design, not subject to test. Note ...
Page 6
LTC1605 W U TYPICAL PERFORMANCE CHARACTERISTICS LTC1605 Nonaveraged 4096 Point FFT Plot 0 –10 f –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 –130 0 SINAD vs Input Frequency ...
Page 7
PIN FUNCTIONS on Pin 15 and bit 8 is output on Pin 22. Bit 7 is output on Pin 6 and the LSB is output on Pin 13. R/C (Pin 24): Read/Convert Input. With CS low, a ...
Page 8
... COMPARATOR LT1364/LT1365 - Dual and quad 50MHz voltage feedback S A amplifiers. 6.3mA supply current per amplifier. Good AC specs. 16-BIT LATCH 1605 • F01 LinearView is a trademark of Linear Technology Corporation ) and the input is overvoltage protected to ±25V. 200Ω 1000pF 33.2k CAP 1605 • F02 Figure 2 ...
Page 9
U U APPLICATIONS INFORMATION Internal Voltage Reference The LTC1605 has an on-chip, temperature compensated, curvature corrected, bandgap reference, which is factory trimmed to 2.50V. The full-scale range of the ADC is equal ) or nominally ±10V. The output of the ...
Page 10
LTC1605 U U APPLICATIONS INFORMATION signal is applied to the input of the ADC and the resulting output codes are collected over a large number of conver- sions. For example in Figure 7 the distribution of output code is shown ...
Page 11
U U APPLICATIONS INFORMATION t 10 R/C CS BUSY ACQUIRE MODE DATA BUS Figure 9. Using CS to Control Conversion and Read Timing t 10 R/C CS BYTE HI-Z PINS HI-Z PINS ...
Page 12
LTC1605 U U APPLICATIONS INFORMATION a read. Again it is recommended that both R/C and CS return high within 3µs after the start of the conversion. Output Data The output data can be read as a 16-bit word or it ...
Page 13
U U APPLICATIONS INFORMATION Figure 12. Component Side Silkscreen for the Suggested LTC1605 Evaluation Circuit ANALOG GROUND PLANE GROUND PLANE Figure 13. Bottom Side Showing Analog Ground Plane W U DIGITAL Figure 14. Component Side Showing Separate Analog and Digital ...
Page 14
LTC1605 U U APPLICATIONS INFORMATION 1605fc ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... NOTE .394 – .419 (10.007 – 10.643) N .037 – .045 (0.940 – 1.143) .004 – .012 (0.102 – 0.305) S28 (WIDE) 0502 LT 0106 REV C • PRINTED IN THE USA © LINEAR TECHNOLOGY CORPORATION 2005 1605fc ...