MCP3550-60E/MS Microchip Technology, MCP3550-60E/MS Datasheet - Page 18
![IC ADC 22BIT 2.7V 1CH 8MSOP](/photos/6/59/65932/mfg_150_c04-111_ms_8-msop_sml.jpg)
MCP3550-60E/MS
Manufacturer Part Number
MCP3550-60E/MS
Description
IC ADC 22BIT 2.7V 1CH 8MSOP
Manufacturer
Microchip Technology
Specifications of MCP3550-60E/MS
Data Interface
Serial, SPI™
Number Of Bits
22
Sampling Rate (per Second)
15
Number Of Converters
1
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
Resolution (bits)
22bit
Sampling Rate
15SPS
Input Channel Type
Differential
Supply Voltage Range - Analog
2.7V To 5.5V
Supply Current
140µA
Digital Ic Case Style
SOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP355XDV-MS1 - BOARD DEV SENSOR APP MCP355XMCP355XDM-TAS - BOARD DEMO TINY APP SNSR MCP355X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP3550-60E/MS
Manufacturer:
MICROCHIP
Quantity:
12 000
MCP3550/1/3
4.4
The MCP3550/1/3 devices accept a fully differential
analog input voltage to be connected to the V
V
is defined by V
range specified for ensured accuracy is from -V
+V
The converter will output valid and usable codes from
-112% to 112% of output range (see Section 5.0
“Serial Interface”) at room temperature. The ±12%
overrange is clearly specified by two overload bits in
the output code: OVH and OVL. This feature allows for
system calibration of a positive gain error.
The absolute voltage range on these input pins extends
from V
above or below this range, the leakage currents of the
ESD diodes will increase exponentially, degrading the
accuracy and noise performance of the converter. The
common mode of the analog inputs should be chosen
such that both the differential analog input range and
absolute voltage range on each pin are within the
specified operating range defined in Section 1.0
“Electrical Characteristics”.
Both the analog differential inputs and the reference
input have switched-capacitor input structures. The
input
alternatively with the input and the reference in order to
process a conversion. The charge and discharge of the
input capacitors create dynamic input currents at the
V
sampling capacitor. This current is a function of the
differential input voltages and their respective common
modes. The typical value of the differential input
impedance is 2.4 MΩ, with V
5V. The DC leakage current caused by the ESD input
diodes, even though on the order of 1 nA, can cause
additional offset errors proportional to the source
resistance at the V
From a transient response standpoint and as a first-
order approximation, these input structures form a
simple RC filtering circuit with the source impedance in
series with the R
of the input switch and the sampling capacitor. In order
to ensure the accuracy of the sampled charge, proper
settling time of the input circuit has to be considered.
Slow settling of the input circuit will create additional
gain error. As a rule of thumb, in order to obtain 1 ppm
absolute measurement accuracy, the sampling period
must be 14 times greater than the input circuit RC time
constant.
DS21950E-page 18
IN-
IN
REF
+ and V
input pins. The differential voltage that is converted
.
SS
capacitors
Differential Analog Inputs
- 0.3V to V
IN
- input pins inversely proportional to the
IN
ON
= V
IN
(switched resistance when closed)
DD
are
+ and V
IN
+ – V
+ 0.3V. If the input voltages are
charged
IN
IN
CM
-. The differential voltage
- input pins.
= 2.5V, V
and
DD
discharged
= V
IN+
REF
REF
and
to
=
4.5
The MCP3550/1/3 devices accept a single-ended
external reference voltage, to be connected on the
V
ADC is a differential voltage with the non-inverting input
connected to the V
connected to the V
voltage is V
reference is always (V
The MCP3550/1/3 devices accept a single-ended
reference voltage from 0.1V to V
output noise is dominated by thermal noise that is
independent of the reference voltage. Therefore, the
output noise is not significantly improved by lowering
the reference voltage at the V
reduced reference voltage will significantly improve the
INL performance since the INL max error is
proportional to V
The charge and discharge of the input capacitor create
dynamic input currents at the V
proportional to the sampling capacitor, which is a func-
tion of the input reference voltage. The typical value of
the single-ended input impedance is 2.4 MΩ, with
V
the ESD input diodes, though on the order of 1 nA
typically, can cause additional gain error proportional to
the source resistance at the V
4.6
The MCP3550/1/3 devices contain an internal Power-
On Reset (POR) circuit that monitors power supply
voltage V
correct device start-up at system power-up and power-
down events. The POR has built-in hysteresis and a
timer to give a high degree of immunity to potential
ripple and noise on the power supplies, as well as to
allow proper settling of the power supply during power-
up. A 0.1 µF decoupling capacitor should be mounted
as close as possible to the V
transient immunity.
The threshold voltage is set at 2.2V, with a tolerance of
approximately ±5%. If the supply voltage falls below
this threshold, the MCP3550/1/3 devices will be held in
a reset condition or in Shutdown mode. When the part
is in Shutdown mode, the power consumption is less
than 1 µA. The typical hysteresis value is around
200 mV in order to prevent reset during brown-out or
other glitches on the power supply.
REF
DD
= V
input pin. Internally, the reference voltage for the
REF
Voltage Reference Input Pin
Power-On Reset (POR)
DD
REF
= 5V. The DC leakage current caused by
during operation. This circuit ensures
REF
- V
SS
SS
2
REF
(see
REF
pin. The value of the reference
and the common mode of the
© 2009 Microchip Technology Inc.
pin and the inverting input
- V
Figure
DD
SS
REF
REF
pin, providing additional
)/2.
REF
input pin. However, a
2-4).
pin.
DD.
input pin inversely
The converter