AD7712ARZ Analog Devices Inc, AD7712ARZ Datasheet - Page 3

• Manufacturer Part Number: AD7712ARZ
• Description: IC ADC SIGNAL COND LC2MOS 24SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD7712ARZ

• Data Interface: Serial
• Number Of Bits: 24
• Sampling Rate (per Second): 1.03k
• Number Of Converters: 1
• Power Dissipation (max): 45mW
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (0.300", 7.50mm Width)
• Resolution (bits): 24bit
• Sampling Rate: 1.028kSPS
• Input Channel Type: Differential
• Supply Voltage Range - Digital: 4.75V To 5.25V
• Supply Current: 4.5mA
• Digital Ic Case Style: SOIC
• Number Of Elements: 1
• Resolution: 24Bit
• Architecture: Delta-Sigma
• Sample Rate: 1.028KSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Rated Input Volt: 5/20/±5/±20V
• Differential Input: Yes
• Power Supply Requirement: Single/Dual
• Single Supply Voltage (typ): 5/10V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 10.5V
• Dual Supply Voltage (typ): ±5/-5/10V
• Dual Supply Voltage (min): ±4.75V
• Dual Supply Voltage (max): -5.25/10.5V
• Power Dissipation: 52.5mW
• Integral Nonlinearity Error: ±0.003%FSR
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Package Type: SOIC W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

SPECIFICATIONS
Parameter
REFERENCE OUTPUT
V
LOGIC INPUTS
LOGIC OUTPUTS
TRANSDUCER BURNOUT
SYSTEM CALIBRATION
NOTES
13
14
15
16
17
REV. F
BIAS
The AD7712 is tested with the following V
with AV
Guaranteed by design, not production tested.
After calibration, if the analog input exceeds positive full scale, the converter will output all 1s. If the analog input is less than negative full scale, then the device will
output all 0s.
These calibration and span limits apply provided the absolute voltage on the AIN1 analog inputs does not exceed AV
than V
The offset calibration limit applies to both the unipolar zero point and the bipolar zero point.
Output Voltage
Initial Tolerance
Drift
Output Noise
Line Regulation (AV
Load Regulation
External Current
Input Voltage Range
V
Input Current
All Inputs except MCLK IN
MCLK IN Only
V
V
Floating State Leakage Current
Floating State Output Capacitance
Current
Initial Tolerance
Drift
AIN1
AIN2
BIAS
OL
OH
V
V
V
V
Positive Full-Scale Calibration Limit
Negative Full-Scale Calibration Limit
Offset Calibration Limit
Input Span
Positive Full-Scale Calibration Limit
Negative Full-Scale Calibration Limit
Offset Calibration Limit
Input Span
INPUT
, Output Low Voltage
, Output High Voltage
INL
INH
INL
INH
SS
Rejection
DD
, Input Low Voltage
, Input Low Voltage
– 30 mV.
, Input High Voltage
, Input High Voltage
= 5 V and V
13
15
15
DD
SS
)
= –5 V, V
16, 17
17
BIAS
14
= 0 V.
(continued)
BIAS
15
15
15
15
voltages. With AV
A, S Versions
2.5
± 1
20
30
1
1.5
1
AV
or AV
or AV
V
or V
or V
65 to 85
± 10
0.8
2.0
0.8
3.5
0.4
4.0
± 10
9
4.5
± 10
0.1
(1.05
–(1.05
–(1.05
0.8
(2.1
(4.2
–(4.2
–(4.2
3.2
(8.4
SS
DD
+ 0.85
SS
SS
DD
DD
V
V
– 0.85
+ 3
+ 2.1
V
V
V
REF
REF
V
V
V
REF
REF
REF
– 3.5
– 2.1
V
V
REF
REF
REF
DD
/GAIN
/GAIN
REF
REF
)/GAIN
)/GAIN
)/GAIN
)/GAIN
)/GAIN
)/GAIN
= 5 V and V
V
)/GAIN
)/GAIN
1
REF
V
REF
–3–
SS
Unit
V nom
% max
ppm/°C typ
µV typ
mV/V max
mV/mA max
mA max
V max
V max
V min
V min
dB typ
µA max
V max
V min
V max
V min
V max
V min
µA max
pF typ
µA nom
% typ
%/°C typ
V max
V max
V max
V min
V max
V max
V max
V max
V min
V max
= 0 V, V
BIAS
= 2.5 V; with AV
Conditions/Comments
pk-pk Noise; 0.1 Hz to 10 Hz Bandwidth
Maximum Load Current 1 mA
See V
Whichever Is Smaller: +5 V/–5 V or +10 V/0 V
Nominal AV
Whichever Is Smaller: +5 V/0 V Nominal AV
See V
Whichever Is Greater: +5 V/–5 V or +10 V/0 V
Nominal AV
Whichever Is Greater: +5 V/0 V Nominal AV
Increasing with Gain
I
I
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
SINK
SOURCE
= 1.6 mA
BIAS
BIAS
= 100 µA
Input Section
Input Section
DD
DD
DD
= 10 V and V
DD
/V
/V
+ 30 mV or does not go more negative
SS
SS
SS
= 0 V, V
BIAS
= 5 V and
AD7712
DD
DD
/V
/V
SS
SS