LTC2498IUHF#PBF Linear Technology, LTC2498IUHF#PBF Datasheet - Page 11

• Manufacturer Part Number: LTC2498IUHF#PBF
• Description: IC ADC 24BIT 16CH 38-QFN
• Manufacturer: Linear Technology

Specifications of LTC2498IUHF#PBF

• Number Of Bits: 24
• Sampling Rate (per Second): 7.5
• Data Interface: MICROWIRE™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 480µW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 38-WFQFN, Exposed Pad
• Number Of Elements: 1
• Resolution: 24Bit
• Architecture: Delta-Sigma
• Sample Rate: 0.008KSPS
• Input Polarity: Bipolar
• Input Type: Voltage
• Rated Input Volt: ±2.75V
• Differential Input: Yes
• Power Supply Requirement: Single
• Single Supply Voltage (typ): 3.3/5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Integral Nonlinearity Error: 10ppm of Vref
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 38
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

pin Functions
SDI (Pin 34): Serial Data Input. This pin is used to select the
line frequency rejection mode, 1x or 2x mode, temperature
sensor, as well as the input channel. The serial data input
is applied under control of the serial clock (SCK) during
the data output/input operation. The first conversion fol-
lowing a new input or mode change is valid.
f
controls the internal conversion clock rate. When f
connected to V
oscillator running at 307.2kHz. The conversion clock may
also be overridden by driving the f
clock in order to change the output rate and the digital
filter rejection null.
CS (Pin 36): Active LOW Chip Select. A LOW on this pin
enables the digital input/output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW-to-HIGH transition on CS
during the Data Output aborts the data transfer and starts
a new conversion.
O
(Pin 35): Frequency Control Pin. Digital input that
CC
or GND, the converter uses its internal
O
pin with an external
O
is
SDO (Pin 37): Three-State Digital Output. During the data
output period, this pin is used as the serial data output.
When the chip select pin is HIGH, the SDO pin is in a high
impedance state. During the conversion and sleep periods,
this pin is used as the conversion status output. When
the conversion is in progress this pin is HIGH; once the
conversion is complete SDO goes LOW. The conversion
status is monitored by pulling CS LOW.
SCK (Pin 38): Bidirectional, Digital I/O, Clock Pin. In Internal
Serial Clock Operation mode, SCK is generated internally
and is seen as an output on the SCK pin . In External Serial
Clock Operation mode, the digital I/O clock is externally
applied to the SCK pin. The Serial Clock operation mode
is determined by the logic level applied to the SCK pin at
power-up and during the most recent falling edge of CS.
Exposed Pad (Pin 39): Ground. This pin is ground and
must be soldered to the PCB ground plane. For prototyping
purposes, this pin may remain floating.
LTC2498

2498fe