MCP3901T-I/SS Microchip Technology, MCP3901T-I/SS Datasheet - Page 3
![IC SPI INTERFACE DUAL-CH 20-SSOP](/photos/6/58/65895/150-20-ssop_sml.jpg)
MCP3901T-I/SS
Manufacturer Part Number
MCP3901T-I/SS
Description
IC SPI INTERFACE DUAL-CH 20-SSOP
Manufacturer
Microchip Technology
Specifications of MCP3901T-I/SS
Number Of Bits
24
Number Of Channels
2
Power (watts)
10mW
Voltage - Supply, Analog
4.5 V ~ 5.5 V
Voltage - Supply, Digital
2.7 V ~ 5.5 V
Package / Case
20-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
1.0
Absolute Maximum Ratings †
V
Digital inputs and outputs w.r.t. A
Analog input w.r.t. A
V
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-65°C to +125°C
Soldering temperature of leads (10 seconds) ............. +300°C
ESD on the analog inputs (HBM,MM) ................. 7.0 kV, 400V
ESD on all other pins (HBM,MM) ........................ 7.0 kV, 400V
ELECTRICAL CHARACTERISTICS
© 2010 Microchip Technology Inc.
Electrical Specifications: Unless otherwise indicated, AV
MCLK = 4 MHz; PRESCALE = 1; OSR = 64; GAIN = 1; Dithering OFF; V
Internal Voltage Reference
Internal Voltage Reference
Tolerance
Temperature Coefficient
Output Impedance
Voltage Reference Input
Input Capacitance
Differential Input Voltage Range
(V
Absolute Voltage on REFIN+ Pin
Absolute Voltage on REFIN- Pin
ADC Performance
Resolution (No Missing Codes)
Sampling Frequency
Note 1:
DD
REF
REF+
...................................................................................7.0V
input w.r.t. A
2:
3:
4:
5:
6:
7:
8:
– V
CHARACTERISTICS
ELECTRICAL
Parameters
REF-
This specification implies that the ADC output is valid over this entire differential range and that there is no dis-
tortion or instability across this input range. Dynamic performance is specified at -0.5 dB below the maximum
signal range, V
See terminology section for definition.
This parameter is established by characterization and not 100% tested.
For these operating currents, the following bit settings apply: SHUTDOWN<1:0> = 00, RESET<1:0> = 00,
VREFEXT = 0, CLKEXT = 0.
For these operating currents, the following Configuration bit settings apply: SHUTDOWN<1:0> = 11,
VREFEXT = 1, CLKEXT = 1.
Applies to all gains. Offset error is dependant on PGA gain setting (see
Outside of this range, the ADC accuracy is not specified. An extended input range of ±6V can be applied
continuously to the part with no risk for damage.
For proper operation and to keep ADC accuracy, AMCLK should always be in the range of 1 to 5 MHz with
BOOST bits off. With BOOST bits on, AMCLK should be in the range of 1 to 8.192 MHz,
AMCLK = MCLK/PRESCALE. When using a crystal, the CLKEXT bit should be equal to ‘0’.
)
GND
GND
............................... -0.6V to V
..................................... ....-6V to +6V
IN
= -0.5 dBFS @ 50/60 Hz = 353 mV
GND
........ -0.6V to V
ZOUT
Symbol
TC
V
V
V
V
REF+
REF-
REF
REF
f
REF
S
REF
DD
DD
+0.6V
+0.6V
-2%
Min
-0.3
2.2
1.9
24
—
—
—
DD
See
= 4.5 to 5.5V, DV
Typical
RMS,
2.37
Table 4-2
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at those or any other conditions, above those indi-
cated in the operational listings of this specification, is not
implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
12
—
—
—
—
—
7
V
REF
IN
= 2.4V.
= -0.5 dBFS = 353 mV
+2%
Max
2.6
2.9
0.3
—
—
10
—
DD
= 2.7 to 5.5V; -40°C < T
Figure 2-19
ppm/°C VREFEXT = 0
Units
kHz
bits
kΩ
pF
V
V
V
V
for typical values).
MCP3901
VREFEXT = 0
AV
VREFEXT = 0
V
VREFEXT = 1
VREFEXT = 1
OSR = 256
(See
f
(4 x PRESCALE)
S
REF
RMS
= DMCLK = MCLK/
DD
Table
= (V
= 5V,
Conditions
@ 50/60 Hz
DS22192C-page 3
A
REF+
< +85°C,
5-3)
– V
REF-
),