205202-6 TE Connectivity, 205202-6 Datasheet - Page 6
![HD 20 DF PIN PLTD](/photos/41/59/415924/prpin2_sml.jpg)
205202-6
Manufacturer Part Number
205202-6
Description
HD 20 DF PIN PLTD
Manufacturer
TE Connectivity
Specifications of 205202-6
Rohs Compliant
YES
Product Type
Contact
Product Series
HDP-20 (Crimp Snap)
Termination Method To Wire/cable
Crimp
Insulation Support
No
Grade
Standard
Contact Retention In Housing
Crimp Snap-In
Solder Tail Contact Plating
Gold Flash over Nickel
Pin Diameter (mm [in])
1.02 [0.040]
Wire Range (mm² [awg])
0.2 - 0.6 [24-20]
Contact Type
Pin
Contact Base Material
Brass
Contact Plating, Mating Area, Material
Gold Flash
Contact Size
20
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Packaging Method
Strip
4.
4.1.
4.2.
4.3.
4.4.
Rev F
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form , fit or function are m ade to the product or m anufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determ ined by developm ent/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product m eets the requirem ents of Figure 1. Failures
attributed to equipm ent, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specim ens resubm itted for qualification. Testing to
confirm corrective action is required before resubm ittal.
Quality Conform ance Inspection
The applicable quality inspection plan shall specify the sam pling acceptable quality level to be used.
Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing
and this specification.
Specim en Selection
Connector housings and contacts shall be prepared in accordance with applicable Instruction
Sheets and selected at random from current production. Test groups shall consist of the following:
1.
2.
3.
4.
Test Sequence
Qualification inspection shall be verified by testing specim ens as specified in Figure 2.
Test Groups 1 and 3 shall consist of 10, size 1 (9 position) crim p-snap connector m ated pairs
(plugs without grounding indents), fully loaded with crim p-snap contacts with insulation
support and crim ped to 24 AW G wire. Group 1 uses gold flash and 30 gold contacts. Group 3
uses only gold flash contacts. Cable clam ps are to be used on all connectors. During vibration
and physical shock tests, screwlocks and m ale screws are to be used to secure the
connectors.
Test Group 2 shall consist of 15 m ated pairs, size 5 (50 position) crim p-snap connectors. Five
m ated pairs are loaded with 18 AW G wires, 5 with 24 AW G wire and 5 with 28 AW G wire.
The plugs have no grounding indents, and the wires are crim ped to contacts without
insulation support. The contacts are gold flash plated. Cable clam ps are to be used on all
connectors.
Test Group 4 shall consist of 30 each of contacts with insulation support crim ped to 24, 26,
and 28 AW G wire. The 18, 20 and 22 AW G wires are crim ped to contacts without insulation
support. The contacts are gold flash plated.
Test Group 5 shall consist of 5 of each size of m ated pairs fully loaded with contacts. The
plugs have grounding indents. The contacts are gold flash plated.
108-40005
6 of 10