DS1307 Maxim Integrated Products, DS1307 Datasheet - Page 10
![IC RTC SERIAL 512K 8-DIP](/photos/1/39/13900/175-8-dip_sml.jpg)
DS1307
Manufacturer Part Number
DS1307
Description
IC RTC SERIAL 512K 8-DIP
Manufacturer
Maxim Integrated Products
Type
Clock/Calendar/NVSRAMr
Datasheet
1.DS1307Z.pdf
(14 pages)
Specifications of DS1307
Memory Size
56B
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
I²C, 2-Wire Serial
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS1307
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS1307+
Manufacturer:
Maxim
Quantity:
7 457
Part Number:
DS1307+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS1307N
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS1307N+
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS1307Z
Manufacturer:
MAXIM
Quantity:
1 564
Part Number:
DS1307Z
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS1307Z+
Manufacturer:
Maxim
Quantity:
10 573
I
The DS1307 supports the I
device receiving data as a receiver. The device that controls the message is called a master. The devices that are
controlled by the master are referred to as slaves. The bus must be controlled by a master device that generates
the serial clock (SCL), controls the bus access, and generates the START and STOP conditions. The DS1307
operates as a slave on the I
Figures 3, 4, and 5 detail how data is transferred on the I
Accordingly, the following bus conditions have been defined:
2
C DATA BUS
Data transfer can be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data
line while the clock line is high will be interpreted as control signals.
Bus not busy: Both data and clock lines remain HIGH.
START data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is HIGH,
defines a START condition.
STOP data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line is HIGH,
defines the STOP condition.
Data valid: The state of the data line represents valid data when, after a START condition, the data line is
stable for the duration of the HIGH period of the clock signal. The data on the line must be changed during the
LOW period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of
data bytes transferred between START and STOP conditions is not limited, and is determined by the master
device. The information is transferred byte-wise and each receiver acknowledges with a ninth bit. Within the
I
The DS1307 operates in the standard mode (100kHz) only.
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the
reception of each byte. The master device must generate an extra clock pulse which is associated with this
acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a way
that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of course,
setup and hold times must be taken into account. A master must signal an end of data to the slave by not
generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave
must leave the data line HIGH to enable the master to generate the STOP condition.
2
C bus specifications a standard mode (100kHz clock rate) and a fast mode (400kHz clock rate) are defined.
2
2
C bus.
C protocol. A device that sends data onto the bus is defined as a transmitter and a
10 of 14
2
C bus.
DS1307 64 x 8, Serial, I
2
C Real-Time Clock