CDP68HC68T1M296 Intersil, CDP68HC68T1M296 Datasheet - Page 8
![IC RTC RAM/SPI SERIAL 16-SOIC](/photos/5/65/56533/20-16-soic_sml.jpg)
CDP68HC68T1M296
Manufacturer Part Number
CDP68HC68T1M296
Description
IC RTC RAM/SPI SERIAL 16-SOIC
Manufacturer
Intersil
Type
Clock/Calendar/NVSRAMr
Datasheet
1.CDP68HC68T1EZ.pdf
(23 pages)
Specifications of CDP68HC68T1M296
Memory Size
32B
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
SPI, 3-Wire Serial
Voltage - Supply
3 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.300", 7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Functional Description
The SPI real-time clock consists of a clock/calendar and a
32x8 RAM. Communications is established via the SPI
(Serial Peripheral Interface) bus. In addition to the
clock/calendar data from seconds to years, and system
flexibility provided by the 32-byte RAM, the clock features
computer handshaking with an interrupt output and a
separate squarewave clock output that can be one of seven
different frequencies. An alarm circuit is available that
compares the alarm latches with the seconds, minutes and
hours time counters and activates the interrupt output when
they are equal. The clock is specifically designed to aid in
power-down/power-up applications and offers several pins
to aid the designer of battery backup systems.
Mode Select
The voltage level that is present at the V
end of power-on-reset selects the device to be in the single
supply or battery backup mode.
Single-Supply Mode
If V
OUT, PSE and CPUR will be enabled and the device will be
completely operational. CPUR will be placed low if the logic
level at the V
PSE and CPUR are disabled due to a power-down instruction,
V
enable these outputs. An example of the single-supply mode is
where only one supply is available and V
are tied together to the supply.
Battery Backup Mode
If V
OUT, PSE and CPUR will be disabled (CLK OUT, PSE and
CPUR low). This condition will be held until V
threshold (about 1.0V) above V
PSE and CPUR will then be enabled and the device will be
operational. If V
outputs CLK OUT, PSE and CPUR will be disabled. An
example of battery backup operation occurs if V
V
connected to the V
V
Clock/Calendar
The clock/calendar portion of this device consists of a long
string of counters that is toggled by a 1Hz input. The 1Hz
input is generated by a prescaler driven by an on-board
oscillator that utilizes one of four possible external crystals or
that can be driven by an external clock source. The 1Hz
trigger to the counters can also be supplied by a 50Hz or
60Hz input source that is connected to the LINE input pin.
The time counters offer seconds, minutes and hours data in
12 hour or 24 hour format. An AM/PM indicator is available
that once set, toggles every 12 hours. The calendar counters
consist of day (day of week), date (day of month), month and
SYS
DD
BATT
SYS
SYS
and V
brought to a logic low and then to a logic high will re-
for Battery Backup Operation on page 11.)
is a logic high when power-on-reset is completed, CLK
is a logic low at the end of power-on-reset, CLK
DD
SYS
is not connected to a supply when a battery is
SYS
pin goes low. If the output signals CLK OUT,
BATT
(See Figures 1 and 2)
falls below a threshold above V
pin. (See "Functional Description",
8
BATT
. The outputs CLK OUT,
DD
SYS
, V
BATT
input pin at the
SYS
SYS
rises to a
and V
BATT
is tied to
CDP68HC68T1
SYS
the
years information. Data in the counters is in BCD format. The
hours counter utilizes BCD for hour data plus bits for 12/24 hour
and AM/PM. The seven time counters are accessed serially at
addresses 20H through 26H. See Table 1.
RAM
The real-time clock also has a static 32x8 RAM that is located
at addresses 00-1FH. Transmitting the address/control word
with Bit 5 low selects RAM access. Bits 0 through 4 select the
RAM location.
Alarm
The alarm is set by accessing the three alarm latches and
loading the required data. The alarm latches consist of
seconds, minutes and hours registers. When their outputs
equal the values in the seconds, minutes and hours time
counters, an interrupt is generated. The interrupt output will go
low if the alarm bit in the Interrupt Control Register is set high.
The alarm interrupt bit in the Status Register is set when the
interrupt occurs (see "Functional Description", INT Pin on
page 10). To preclude a false interrupt when loading the time
counters, the alarm interrupt bit should be set low in the
Interrupt Control Register. This procedure is not required when
the alarm time is set.
Watchdog Function (
When Bit 7 in the Interrupt Control Register is set high, the
Clock’s CE (chip enable) pin must be toggled at a regular
interval without a serial data transfer. If the CE is not toggled,
the clock will supply a CPU reset pulse and Bit 6 in the Status
Register will be set. Typical service and reset times are listed in
Table 2.
Clock Out
The value in the three least significant bits of the Clock Control
Register selects one of seven possible output frequencies.
(See “Clock Control Register” on page 11). This squarewave
signal is available at the CLK OUT pin. When power-down
operation is initiated, the output is set low.
Control Registers and Status Registers
The operation of the Real-Time Clock is controlled by the Clock
Control and Interrupt Control Registers. Both registers are
Read-Write Registers. Another register, the Status Register, is
available to indicate the operating conditions. The Status
Register is a Read only Register.
Power Control
Power control is composed of two operations, Power Sense
and Power-Down/Power-Up. Two pins are involved in power
sensing, the LINE input pin and the INT output pin. Two
additional pins are utilized during power-down/power-up
operation. They are the PSE (Power Supply Enable) output
pin and V
Service Time
Reset Time
SYS
input pin.
MIN
20
-
50Hz
10ms
40ms
MAX
See Figure 6
TABLE 2.
MIN
16.7
-
60Hz
)
33.3ms
8.3ms
MAX
15.6
MIN
-
October 29, 2007
XTAL
31.3ms
7.8ms
FN1547.8
MAX