179610-1 TE Connectivity, 179610-1 Datasheet - Page 6

• Manufacturer Part Number: 179610-1
• Description: AMP CT CRIMP-2 REC CONT. L/P
• Manufacturer: TE Connectivity

Specifications of 179610-1

• Product Type: Contact
• Termination Method To Wire/cable: Crimp
• Contact - Rated Current (a): 2
• Operating Voltage Reference: AC/DC, AC, DC
• Operating Voltage (vac): 125
• Operating Voltage (vdc): 125
• Wire/cable Size (awg): 26 – 30
• Mating Retention: Without
• Contact Type: Socket
• Contact Plating, Mating Area, Material: Pre-Tin
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Operating Temperature (°c [°f]): -30 – +105 [-22 – +221]
• Applies To: Wire/Cable
• Accepts Wire Insulation Diameter, Range (mm [in]): 0.65 – 1.35 [0.0255 – 0.053]
• Application Use: Wire-to-Board, Wire-to-Board / Wire-to-Wire, Wire-to-Wire
• Contact Transmits (typical Application): Signal (Data)
• Packaging Method: Loose Piece

ASHL-0005- ES REV B
3.8.3 (1)
3.8.3 (2)
3.8.3 (3)
3.8.3 (4)
3.8.3 (5)
3.8.3 (6)
3.8.3 (7)
Para.
Vibration
Sinusoidal
Low Frequency
Physical Shock
Temperature
Life
Resistance to
Cold
Humidity,
Steady State
Thermal Shock
Salt Spray
Test Items
AMP Shanghai Ltd.
Tyco Electronics
No electrical discontinuity greater than 1
microsecond shall occur.
Termination resistance (low level) shall be
met.
No electrical discontinuity greater than 1
microsecond shall occur.
Termination resistance (low level) shall be
met.
Termination resistance (low level) shall be
met.
Termination resistance (low level) shall be
met.
Insulation resistance (Final) 500 MΩ Min.
Termination resistance (low level) shall be
met.
Termination resistance (low level) shall be
met.
Resistance (low level) (Final) must meet
visual & electrical requirements, which
applicable.
Environmental Performance Requirements
Fig. 2 (To be continued)
Requirements
6 of 11
PAGE
Document No.
108-5408
Subject mated connectors to 10-
55-10 Hz traversed in 1 minute
at 1.52 mm amplitude 2 hours
each of 3 mutually
perpendicular planes.
MIL-STD-202, Method 201,
Condition A.
Subject mated connectors to
490.3 m/s
pulses of 11milisecond
duration; 3 shocks in each
direction applied along the 3
mutually perpendicular planes
total 18 shocks.
MIL-STD-202, Method 213,
Condition A.
Subject mated connectors to
temperature life; testing
atmosphere at 85±2
hours.
Subject mated connectors to
cold testing atmosphere at -25
±3
Subsequent measurement shall
be done after reconditioning in
the room temperature for 1
hour.
Subject mated connectors to
steady state humidity at 40
and 90~95 % R.H.
MIL-STD-202, Method 103,
Condition B.
Subject mated connectors to 5
cycles between -55
for 30 minutes each duration at
temperature extremes.
MIL-STD-202, Method 107,
Condition A.
Subject mated/unmated
connectors to 5% salt
concentration for 48 hours.
MIL-STD-202, Method 101,
Condition B.
o
C for 48 hours.
2
Procedures
halfsine shock
o
o
C and 85
REV
C for 96
B
o
C
o
C
LOC
ES