1617069-9 TE Connectivity, 1617069-9 Datasheet - Page 4

• Manufacturer Part Number: 1617069-9
• Description: DS13-1002 = DS13 SOLID STATE D
• Manufacturer: TE Connectivity

Specifications of 1617069-9

• Input Type: DC
• Output Type: DC
• Input Voltage (max): 32V
• Output Voltage (max): 60V
• Input Current (max): 15mA
• Output Current: 2A
• Output Device: MOSFET
• Operating Temperature Classification: Industrial
• Rad Hardened: No
• Lead Free Status / Rohs Status: Not Compliant

4
Figure 7 - Outline Dimensions
Notes
1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is
2.Vcc = 5Vdc for all tests unless otherwise specified.
3.All DS13 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent
4.Transient blocking voltage & electrical system spike tests are performed per MIL-STD-704 (28Vdc systems).
5.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25°C by normalized on-resistance factor from curve (Fig. 4).
6.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 90091.
7.Proper operation of the status feedback requires a status pull-up resistor. Select the status resistor such that it limits status output current to 2mA: R status = V
DS13-TBD–PDF–KRG–1-04
www.tycoelectronics.com
required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value form the curve.
damage. Inductive loads must be diode suppressed.
Load circuit series inductance for “load shorted” mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10
Hz. To calculate maximum on-resistance at any temperature, use the following equation: R(on) = R(on) @ 25°C x NF (without short circuit protection) and R(on) =
0.2 x NF + .21 (with short circuit protection) where NF = normalized on-resistance factor from Fig. 4.
status – 0.3V / 2mA.
(10.16 ± .38)
.400 ± .015
.016 +.010, –.005
(.41 +.25, –.13)
6 PLS
.010 ± .002
(.25 ± .05)
6 PLS
Through-Hole Mount Version
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
(2.54)
.100
(3.18)
.125
TOP INDEX MARK FOR PIN 1
SIDE INDEX MARK FOR PIN 1
DS13 Series High Performance Solid State Relays
DC solid state relay for loads up to 2A @ 60Vdc
8
1
.560 MAX.
(14.22)
(7.62)
.300
2
7
5
4
(3.81 ± .38)
.150 ± .015
.018 ± .002
(.46 ± .05)
6 PLS
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
6 PLS
.395 MAX.
(10.03)
.155 MAX.
(3.94)
.485 +.010, –.005
(12.32 +.25, –.13)
6 PLS
(.64)
.025
.036 +.010, –.005
(.91 +.25, –.13)
.435 MAX.
(11.05)
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
6 PLS
.010 ± .002
(.25 ± .05)
6 PLS
Surface Mount Version
(2.54)
.100
(3.18)
.125
(Continued)
SIDE INDEX MARK FOR PIN 1
TOP INDEX MARK FOR PIN 1
1
8
.560 MAX.
(14.22)
(7.62)
.300
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
2
7
4
5
.018 ± .002
(.46 ± .05)
6 PLS
.395 MAX.
.155 MAX.
(10.03)
(3.94)