1-1877285-2 TE Connectivity, 1-1877285-2 Datasheet - Page 3
![EP HEADER ASY,SHROUDED,12 POSITION](/photos/40/39/403981/pr1877285_sml.jpg)
1-1877285-2
Manufacturer Part Number
1-1877285-2
Description
EP HEADER ASY,SHROUDED,12 POSITION
Manufacturer
TE Connectivity
Specifications of 1-1877285-2
Voltage Rating
250 VAC
Current Rating
7.5 A
Pitch
3.96 mm
Number Of Rows
1
Mounting Style
Through Hole
Termination Style
Solder
Housing Material
Polybutylene Terephthalate
Contact Material
Brass
Contact Plating
Tin over Nickel
Number Of Positions / Contacts
12
Product Line
Economy Power
Product Type
Connector
Connector Type
Header
Pcb Mounting Orientation
Vertical
Pcb Mount Retention
Without
Pcb Mount Alignment
With
Termination Method To Pc Board
Through Hole - Solder
Sealed
No
Mating Retention Type
Latching
Contact - Rated Current (a)
7.5
Operating Voltage Reference
AC
Operating Voltage (vac)
250
Tail Orientation
In-line
Tail Length (mm [in])
3.7 [0.146]
Profile Height (y-axis) (mm [in])
12.00 [0.472]
Centerline (mm [in])
3.96 [0.156]
Header Type
Shrouded
Number Of Positions
12
Selectively Loaded
No
Mating Retention
With
Length (x-axis) (mm [in])
50.77 [1.9988]
Width (z-axis) (mm [in])
9.58 [0.377]
Contact Type
Pin
Contact Base Material
Brass
Contact Plating, Mating Area, Material
Tin
Contact Plating, Mating Area, Thickness (µm [?in])
0.8 [31.5]
Contact Design
Square Post
Tail Plating Material
Tin
Tail Plating, Thickness (µm [?in])
0.8 [31.46]
Connector Style
Plug
Housing Color
Black
Mating Alignment
With
Ul Flammability Rating
UL 94V-0
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Operating Temperature (°c [°f])
-25 – +105 [-13 – +221]
Applies To
Printed Circuit Board
Pcb Thickness, Recommended (mm [in])
1.60 [0.063]
Contact Transmits (typical Application)
Power
Lead Free Status / Rohs Status
Details
Mechanical shock.
Durability.
Mating force.
Unmating force.
Crimp tensile.
Contact retention.
Thermal shock.
Humidity/temperature cycling.
Temperature life.
Rev O5
NOTE
Test Description
Shall meet visual requirements, show no physical damage, and meet requirements of additional
tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure
2.
No discontinuities of 1 microsecond
or longer duration.
See Note.
See Note.
9.8 N [2.2 lbf] maximum per
contact.
0.9 N [0.22 lbf] minimum per
contact.
29.4 N [6.6 lbf] minimum per
contact.
See Note.
See Note.
See Note.
Wire Size
(AWG)
22
20
18
16
ENVIRONMENTAL
Figure 1 (end)
Requirement
N [lbf] Minimum
Crimp Tensile
44.5 [10]
62.3 [14]
75.6 [17]
120 [27]
EIA-364-27, Condition H.
Subject mated specimens to 30 G's
half-sine shock pulses of 11
milliseconds duration. Three shocks
in each direction applied along 3
mutually perpendicular planes, 18
total shocks.
EIA-364-9.
Mate and unmate specimens for 15
cycles at a maximum rate of 500
cycles per hour.
EIA-364-13.
Measure force necessary to mate
specimens with latches disengaged
at a maximum rate of 12.7 mm per
minute.
EIA-364-13.
Measure force necessary to unmate
specimens with latches disengaged
at a maximum rate of 12.7 mm per
minute.
EIA-364-8.
Determine crimp tensile at a rate of
25.4 mm per minute.
EIA-364-29.
Apply axial load at a rate of 4.4 N
per second and hold for 6 seconds.
EIA-364-32, Test Condition VII.
Subject specimens to 10 cycles
between -55 and 105° C with 30
minute dwells at temperature
extremes.
EIA-364-31, Method III.
Subject specimens to 10 cycles (10
days) between 25 and 65° C at 80 to
100% RH.
EIA-364-17, Method A, Test
Condition 4, Test Time Condition C.
Subject mated specimens to 105° C
for 500 hours.
Procedure
108-2297
3 of 6