1-1877285-0 TE Connectivity, 1-1877285-0 Datasheet - Page 5
![EP HEADER ASY,SHROUDED,10 POSITION](/photos/40/39/403981/pr1877285_sml.jpg)
1-1877285-0
Manufacturer Part Number
1-1877285-0
Description
EP HEADER ASY,SHROUDED,10 POSITION
Manufacturer
TE Connectivity
Specifications of 1-1877285-0
Voltage Rating
250 VAC
Current Rating
7.5 A
Pitch
3.96 mm
Number Of Rows
1
Mounting Style
Through Hole
Termination Style
Solder
Housing Material
Polybutylene Terephthalate
Contact Material
Brass
Contact Plating
Tin over Nickel
Number Of Positions / Contacts
10
Product Line
Economy Power
Product Type
Connector
Connector Type
Header
Pcb Mounting Orientation
Vertical
Pcb Mount Retention
Without
Pcb Mount Alignment
With
Termination Method To Pc Board
Through Hole - Solder
Sealed
No
Mating Retention Type
Latching
Contact - Rated Current (a)
7.5
Operating Voltage Reference
AC
Operating Voltage (vac)
250
Tail Orientation
In-line
Tail Length (mm [in])
3.7 [0.146]
Profile Height (y-axis) (mm [in])
12.00 [0.472]
Centerline (mm [in])
3.96 [0.156]
Header Type
Shrouded
Number Of Positions
10
Selectively Loaded
No
Mating Retention
With
Length (x-axis) (mm [in])
42.85 [1.687]
Width (z-axis) (mm [in])
9.58 [0.377]
Contact Type
Pin
Contact Base Material
Brass
Contact Plating, Mating Area, Material
Tin
Contact Plating, Mating Area, Thickness (µm [?in])
0.8 [31.5]
Contact Design
Square Post
Tail Plating Material
Tin
Tail Plating, Thickness (µm [?in])
0.8 [31.46]
Connector Style
Plug
Housing Color
Black
Mating Alignment
With
Ul Flammability Rating
UL 94V-0
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Operating Temperature (°c [°f])
-25 – +105 [-13 – +221]
Applies To
Printed Circuit Board
Pcb Thickness, Recommended (mm [in])
1.60 [0.063]
Contact Transmits (typical Application)
Power
Lead Free Status / Rohs Status
Details
4.
4.1.
4.2.
4.3.
4.4.
Rev O5
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to
confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan shall specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Each test group shall consist of a minimum of 5
specimens.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 2.
LLCR Measurement Points
Figure 3
108-2297
5 of 6