MK1714-01RLFTR IDT, Integrated Device Technology Inc, MK1714-01RLFTR Datasheet
MK1714-01RLFTR
Specifications of MK1714-01RLFTR
Related parts for MK1714-01RLFTR
MK1714-01RLFTR Summary of contents
Page 1
... EMI amplitude peaks at the odd harmonics by several dB. The OE pin places both outputs into a high impedance state for board level testing. The PD pin powers down the entire chip and the outputs are held low. See the MK1714-02 for other selections on input ranges and spreads. Block Diagram S4:0 ...
Page 2
... Note: When changing the input frequency, the LEE pin must be set low for minimum allow the PLL to lock to the new frequency. Alternatively, the PD pin may be set low while changing frequencies. IDT™ SPREAD SPECTRUM MULTIPLIER CLOCK REF OE PD GND GND LEE XSEL Pin Description 2 SSCG MK1714-01 REV L 051310 ...
Page 3
... Amount (%) C ±1.25 C ±0 ±1 C ±1 C ±0.5 DC +0.25, -1.25 DC +0. ±1 C ±0.5 DC +0.5, -1 +0.5, -1.5 DC +0.5, -1.5 D -2.5 DC +0.5, -1 -1.5 C ±0.5 DC +0.25, -1. +0. +0. ±1 C ±1 C ±1 C ±1 DC +0.25, -1.25 DC +0.5, -1.5 DC +0. +0.5, -1.5 MK1714-01 REV L 051310 SSCG ...
Page 4
... MK1714-01 input signal should not be applied to X1 until VDD is stable (within 10% of its final value). This requirement can be easily met by operating the MK1714-01 and the X1 source from the same power supply. This requirement is not applicable if a crystal is used. 2) LEE should not be enabled (taken high) until after the power supplies and input clock are stable. This requirement can be met by direct control of LEE by system logic ...
Page 5
... SPREAD SPECTRUM MULTIPLIER CLOCK Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK1714-01. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. ...
Page 6
... JA 3 m/s air flow JA JC Marking Diagram Min. Typ. Max. Units 10 25 MHz 10 150 MHz 1 ±150 200 MHz 1 ppm Min. Typ. Max. Units 135 C/W 93 C/W 78 C/W 60 C/W (MK1714-01RILF MK171401RIL ####### YYWW 1 10 MK1714-01 REV L 051310 SSCG ...
Page 7
... MK1714-01 SPREAD SPECTRUM MULTIPLIER CLOCK 5. Bottom marking: (origin). Origin = country of origin of not USA. IDT™ SPREAD SPECTRUM MULTIPLIER CLOCK 7 SSCG MK1714-01 REV L 051310 ...
Page 8
... Ordering Information Part / Order Number Marking MK1714-01RLF MK1714-01RLFTR see page 7 MK1714-01RILF MK1714-01RILFTR "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use ...
Page 9
... MK1714-01 SPREAD SPECTRUM MULTIPLIER CLOCK Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc ...