DS1099U-CC+ Maxim Integrated Products, DS1099U-CC+ Datasheet - Page 6
![IC ECONOSCILLATOR DUAL 8USOP](/photos/1/39/13936/406-8-msop_sml.jpg)
DS1099U-CC+
Manufacturer Part Number
DS1099U-CC+
Description
IC ECONOSCILLATOR DUAL 8USOP
Manufacturer
Maxim Integrated Products
Series
EconOscillator™r
Type
Clock Generatorr
Datasheet
1.DS1099U-FF.pdf
(6 pages)
Specifications of DS1099U-CC+
Pll
No
Input
Clock
Output
CMOS, TTL
Number Of Circuits
1
Ratio - Input:output
1:2
Differential - Input:output
No/No
Frequency - Max
262kHz
Divider/multiplier
Yes/No
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Frequency-max
262kHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
6 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2007 Maxim Integrated Products
Low-Frequency Dual EconOscillator
The divider settings, X
grammed. When placing an order for the DS1099, it is
required to specify X
it is recommended that the unused output be disabled.
The oscillator outputs are asynchronous. Since the
master oscillator and dividers are free running, even
when both outputs are disabled, the state of the output
when OE becomes active is unknown for up to half an
f
enabled instantaneously. Likewise, if the output is dis-
abled while outputting the low half of a cycle, the out-
put instantaneously is forced high before the current
cycle is completed.
The package branding includes
of the package next to or below 1099.
OUT
G
M
Q
W
A
B
C
D
H
K
N
R
U
Ordering Information (continued)
E
F
J
L
P
S
T
X
Y
Z
period. When OE is brought low, the output is
DIVISOR
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
10
11
12
13
14
15
16
17
18
19
20
21
22
0
1
2
3
4
5
6
7
8
9
0
Branding Information
and X
0
1
and X
. If only one output is used,
1
0
, are factory pro-
and
32.750kHz
16.375kHz
1.048MHz
0.524MHz
0.262MHz
0.131MHz
65.50kHz
8.187kHz
4.093kHz
2.046kHz
1.023kHz
511.7Hz
255.8Hz
127.9Hz
63.96Hz
31.98Hz
0.25Hz
0.5Hz
f OUT
16Hz
8Hz
4Hz
2Hz
1Hz
1
on the top
To achieve best results, it is highly recommended that
a decoupling capacitor is used on the IC power-supply
pins. Typical values of decoupling capacitors are
0.01µF and 0.1µF. Use a high-quality, ceramic, sur-
face-mount capacitor, and mount it as close as possi-
ble to the V
inductance.
TRANSISTOR COUNT: 4221
SUBSTRATE CONNECTED TO GROUND
For the latest package outline information, go to
www.maxim-ic.com/DallasPackInfo.
Pages changed at Rev 1: 1, 2, 3, 5, 6
is a registered trademark of Maxim Integrated Products, Inc.
CC
and GND pins of the IC to minimize lead
Application Information
Package Information
Power-Supply Decoupling
Revision History
Chip Topology