ADN2811ACP-CML Analog Devices Inc, ADN2811ACP-CML Datasheet - Page 12
![IC RECOVER CLOCK/DATA 48-LFCSP](/photos/6/50/65022/cp-48-8_sml.jpg)
ADN2811ACP-CML
Manufacturer Part Number
ADN2811ACP-CML
Description
IC RECOVER CLOCK/DATA 48-LFCSP
Manufacturer
Analog Devices Inc
Type
Clock and Data Recovery (CDR)r
Datasheet
1.ADN2811ACPZ-CML.pdf
(20 pages)
Specifications of ADN2811ACP-CML
Rohs Status
RoHS non-compliant
Output
CML
Frequency - Max
2.7GHz
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-LFCSP
Frequency-max
2.7GHz
Input
-
ADN2811
FUNCTIONAL DESCRIPTION
CLOCK AND DATA RECOVERY
The ADN2811 recovers clock and data from serial bit streams at
OC-48 as well as the 15/14 FEC rates. The data rate is selected
by the RATE input (see Table 4).
Table 4. Data Rate Selection
RATE
0
1
LIMITING AMPLIFIER
The limiting amplifier has differential inputs (PIN/NIN) that
are internally terminated with 50 Ω to an on-chip voltage ref-
erence (VREF = 0.6 V typically). These inputs are normally
ac-coupled, although dc coupling is possible as long as the input
common-mode voltage remains above 0.4 V (see Figure 22,
Figure 23, and Figure 24). Input offset is factory trimmed to
achieve better than 4 mV typical sensitivity with minimal drift.
The limiting amplifier can be driven differentially or single-
ended.
SLICE ADJUST
The quantizer slicing level can be offset by ±100 mV to mitigate
the effect of amplified spontaneous emission (ASE) noise by
applying a differential voltage input of ±0.8 V to SLICEP/N
inputs. If no adjustment of the slice level is needed, SLICEP/N
should be tied to VCC.
LOSS OF SIGNAL (LOS) DETECTOR
The receiver front end level signal detect circuit indicates when
the input signal level has fallen below a user adjustable
threshold. The threshold is set with a single external resistor
from Pin 1, THRADJ, to GND. The LOS comparator trip point
versus the resistor value is illustrated in Figure 4 (this is only
valid for SLICEP = SLICEN = VCC). If the input level to the
ADN2811 drops below the programmed LOS threshold,
SDOUT (Pin 45) indicates the loss of signal condition with a
Logic 1. The LOS response time is ~300 ns by design, but is
dominated by the RC time constant in ac-coupled applications.
If the LOS detector is used, the quantizer slice adjust pins must
both be tied to VCC. This is to avoid interaction with the LOS
threshold level.
Note that it is not expected to use both LOS and slice adjust at
the same time; systems with optical amplifiers need the slice
adjust to evade ASE. However, a loss of signal in an optical link
that uses optical amplifiers causes the optical amplifier output
to be full-scale noise. Under this condition, the LOS would not
detect the failure. In this case, the loss of lock signal indicates
the failure because the CDR circuitry is unable to lock onto a
signal that is full-scale noise.
Data Rate
OC-48
OC-48 FEC
Frequency (MHz)
2488.32
2666.06
Rev. B | Page 12 of 20
REFERENCE CLOCK
There are three options for providing the reference frequency to
the ADN2811: differential clock, single-ended clock, or crystal
oscillator. See Figure 14, Figure 15, and Figure 16 for example
configurations.
OSC
VCC
CLK
19.44MHz
Figure 15. Single-Ended REFCLK Configuration
Figure 14. Differential REFCLK Configuration
Figure 16. Crystal Oscillator Configuration
OUT
REFCLKN
REFCLKP
VCC
VCC
VCC
VCC
VCC
VCC
NC
VCC
REFCLKN
NC
REFCLKP
REFCLKP
REFCLKN
XO1
XO2
XO1
XO2
XO1
XO2
REFSEL
ADN2811
REFSEL
REFSEL
100kΩ
ADN2811
OSCILLATOR
ADN2811
100kΩ
CRYSTAL
100kΩ
OSCILLATOR
OSCILLATOR
CRYSTAL
CRYSTAL
100kΩ
100kΩ
100kΩ
BUFFER
BUFFER
BUFFER
VCC/2
VCC/2
VCC/2