3003R-67X-0001 Curtis Instruments Inc, 3003R-67X-0001 Datasheet - Page 3

• Manufacturer Part Number: 3003R-67X-0001
• Description: METER MAINTENANCE 2"RND 12-48VDC
• Manufacturer: Curtis Instruments Inc
• Series: enGage™ II, 3000r
• Type: Programmable Maintenance Monitor with Hour Meterr

Specifications of 3003R-67X-0001

• Shape: Circular
• Voltage Rating: 12 ~ 48V
• Display Type: LCD - 10 Segment Bar, 5 Digits
• Operating Temperature: -40°C ~ 85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 17631703-67X-0001; 267-1033

The enGage™II 3000 Series is not serviceable.
 This instrument was manufactured and tested
according to the applicable technical standards. It
complies with all the safety regulations as shipped
from the factory.
 Installation and startup must be performed by skilled
personnel.
 Failure to install and operate the unit in accordance
with these instructions may result in damage or injury.
 If safe operation of the instrument can no longer be
ensured, stop and secure it against accidental
operation.
 If instrument failure or malfunction may cause
personal injury or material damage, use additional
safety measures such as limit switches, guards, etc.
 Read the Operating Instructions carefully before
startup.
 Note the safety instructions marked with this
warning symbol in this manual.
Curtis Instruments’ products and/or components are
guaranteed against defects in workmanship and
material for a period of two years, or as defined in the
individual product literature, from date of shipment
from our factory, when applied in a proper application
within specified ratings. This guarantee is limited to
repair or replacement F.O.B. our factory. There is no
further warranty or implied representation, guarantee,
promise or agreement as to any Curtis Instruments
product and/or component. Curtis Instruments, Inc.,
cannot assume responsibility or accept invoices for
unauthorized repairs to its products and/or
components, even though defective. In no case will
Curtis Instruments’ responsibility extend to products,
components or equipment not of its manufacture.
Under no circumstances shall Curtis Instruments, Inc.
be liable for any special or consequential damages or
loss of profits or other damages. Returned goods will
not be accepted unless identified by a Curtis Return
Material Authorization (RMA). All specifications are
subject to change without notice.
Safety Instructions
Maintenance
Guarantee
1.
indicate that an hour meter is displayed in the numeric
display. Flashes to indicate hour meter accumulation.
2.
indicate that the maintenance hour meter is displayed
in the numeric display. Flashes when the maintenance
interval is reached.
3.
day clock is being displayed in the numeric display and
that time is counting-up.
4.
the maintenance hour meter
5.
interval or level.
Will not/can not configure
1.
2.
3.
4.
maintenance interval
Decimal Point - To indicate 1/10 of an hour on
Colon - Flashes to indicate that the time-of-
Percent - Indicates remaining percentage of
Wrench Icon - Turned on (not blinking) to
Mating connector; 8-pin AMP, P/N 794821-1
with UL rating 94V-0.
794772-0.
P/N770904-X for #18-24 AWG.
Material:
polymethylmethacrylat
overlay and mounting bracket-polycarbonate.
This unit is designed for a mounting panel
thickness of 0.8mm-6.4mm.
Panel cutout:
hole.
Will not reset
Hourglass Icon - Turned on (not blinking) to
Maintenance Monitor Function
Problem
Troubleshooting
LCD Icons
Case-polycarbonate, lens-clear
Notes
Wire
52mm diameter dash panel
seal
Resetting
procedure not being
followed
No Power to set up
enable pin
Possible Cause
Interface seal, P/N
(PMMA)
794758-1,
3
cover,
Pins