ACA5-20RM-5-AC4-RL-C Murata Power Solutions Inc, ACA5-20RM-5-AC4-RL-C Datasheet - Page 4

• Manufacturer Part Number: ACA5-20RM-5-AC4-RL-C
• Description: AMMETER AC 200A 220VAC RED
• Manufacturer: Murata Power Solutions Inc
• Series: ACA5-20RMr
• Type: Ammeterr

Specifications of ACA5-20RM-5-AC4-RL-C

• Display Type: LED
• Measuring Range: 0 ~ 199.9A
• Display Style: Red Characters, Black Background
• Display Digits: 3.5
• Display Digits - Height: 0.370" (9.40mm)
• Backlight: Without
• Mounting Type: Panel Mount
• Termination: Terminal Block
• Voltage - Supply: 170 ~ 264VAC
• Dimensions: 53.34 mm L x 35.56 mm W x 18.54 mm H
• Mounting Style: Panel
• Primary Voltage Rating: 170 V to 264 V
• Secondary Current Rating: 199.9 A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Display Face Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 811-1977

BEZEL AND PANEL CUTOUT
PANEL INSTALLATION
All connections to ACA-20RM Series ammeters must be made after
the ammeter is securely attached to the panel and with all associated
load and supply voltages de-energized (off), using extreme caution and
observing all safety measures applicable to the user’s installation.
Care should be exercised when passing conductors through the amme-
ter’s built-in toroid sensor L1. The installed wire-positions should be such
that minimal mechanical forces are applied to L1, TB1, or to the ammeter
itself. In high-vibration environments, it is strongly recommended that
adequate strain reliefs be used for all wiring.
Using Figure 3 as a guide, carefully insert the bezel/color fi lter assembly
into the panel opening. From the rear of the panel, install the four round
Bezel
Gasket
FRONT V IEW
1.826 ( 46.38)
PANEL
SIDE VIEW
(4.75)
0.187
(32.51)
Standoff
1.280
www.murata-ps.com/dpm
Nut
Figure 3. Panel Installation
AC Ammeter
ACA5-20RM
(17.5)
0.69
(27.18)
0.093 ( 2.362) D IAMETER ( 4 R EQUIRED)
plastic standoffs over the bezel’s threaded studs. Install the ACA5-20RM
pc-board assembly as shown and then attach and securely tighten all
four hex nuts. Use only the factory-supplied hardware as the use of sub-
stitute hardware could result in an unsafe installation and/or adversely
affect the reliability of the ammeter.
The recommended range of panel thickness that can be used with the
supplied hardware is 0.040 inches (1.0mm) to 0.125 inches (3.2mm).
Panel thickness outside of this range will require additional user-supplied
hardware or modifi cations.
0.032 (0.8) Thick
1.07
Gasket
INTERNAL C ORNER R ADII:
True-rms-AC Ammeters with 5A CT Inputs
PANEL C UTOUT D IMENSIONS
RECOMMENDED D RILL A ND
0.032 ( 0.81) M AX.
1.336 ( 33.93)
1.626 ( 41.30)
ACA5-20RM Series
26 Jan 2011 MPM_ACA5-20RM.A04 Page 4 of 5
Standoff
0.190 (4.83)
email: [e-mail]
0.145 ( 3.68)
0.116 ( 2.95)
(21.29)
0.838