CUB70000 Red Lion Controls, CUB70000 Datasheet - Page 4
![COUNTER 8-DIGIT REFLECTIVE DISP](/photos/6/45/64535/cub70000_sml.jpg)
CUB70000
Manufacturer Part Number
CUB70000
Description
COUNTER 8-DIGIT REFLECTIVE DISP
Manufacturer
Red Lion Controls
Series
CUB7r
Specifications of CUB70000
Count Rate
10kHz
Number Of Digits/alpha
8
Input Type
Voltage, Switch Closure, Transistor Switch
Voltage - Supply
9 V ~ 28 V
Display Type
LCD Non-Backlit
No. Of Digits / Alpha
8
Digit Height
8.9mm
Supply Voltage Range
9V DC To 28V DC
Operating Temperature Range
0°C To +50°C
Bezel Height
28mm
Bezel Width
51mm
Character Size
9mm
Character Type
7 Segment
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Other names
RLC700
Red Lion Controls
20 Willow Springs Circle
York PA 17402
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
INSTALLATION ENVIRONMENT
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
Do NOT use solvents.
the bezel.
the keypad of the unit.
Installation
indoor use, when properly installed. The units are intended to be mounted into
an enclosed panel. The viewing window and reset button are factory sealed for
a washdown environment. A sponge rubber gasket and mounting clip are
provided for installing the unit in the panel cut-out.
1. Cut panel opening to specified dimensions. Remove burrs and clean around
2. Carefully remove and discard the center section of the gasket. Slide the
3. Install CUB7 unit through the panel cut-out until front bezel flange contacts
4. Slide the mounting clip over the rear of the unit until the clip is against the
The unit should be installed in a location that does not exceed the maximum
The bezel should be cleaned only with a soft cloth and neutral soap product.
Continuous exposure to direct sunlight may accelerate the aging process of
Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate
The CUB7 series of products meets NEMA 4X/IP65 requirements for
The following procedure assures proper installation:
panel opening.
panel gasket over the rear of the unit to the back of the bezel. Insert the
mounting screws onto both sides of mounting clip. Tip of screw should
NOT project from hole in mounting clip.
the panel.
back of the panel. The mounting clip has latching features which engage
into mating features on the CUB7 housing.
ORDERING INFORMATION
TROUBLESHOOTING
company numbers listed.
*Battery is included with unit.
For more information on Pricing, Enclosures & Panel Mount Kits refer to the
RLC Catalog or contact your local RLC distributor.
MODEL NO.
For further technical assistance, contact technical support at the appropriate
*CUB7
BNL
DESCRIPTION
Counter Positive Image Reflective
Counter W/Yel-Grn Backlighting
Counter W/Red Backlighting
3 V Lithium Battery
5. Alternately tighten each screw to ensure uniform gasket pressure.
6. If gasket is not adequately compressed and the mounting screws can no
7. Repeat from step #5 for tightening mounting screws.
Note: It is necessary to hold the unit in place when sliding mounting clip
Visually inspect the front panel gasket. The gasket should be compressed to
about 75 to 80% of its original thickness. If not, gradually turn mounting
screws to further compress gasket.
longer be turned, loosen mounting screws, and check that mounting clip is
latched as close as possible to the panel.
into position.
PART NUMBERS
CUB70000
CUB70010
CUB70020
BNL10000
Fax +31 (0) 334 893 793
NL - 3821 BR Amersfoort
Tel +31 (0) 334 723 225
Red Lion Controls BV
Basicweg 11b