H7CX-A114D1 DC12-24/AC24 Omron, H7CX-A114D1 DC12-24/AC24 Datasheet - Page 30
![COUNTER 11-PIN 12VDC 4DIGIT SPDT](/photos/21/40/214032/3763360_sml.jpg)
H7CX-A114D1 DC12-24/AC24
Manufacturer Part Number
H7CX-A114D1 DC12-24/AC24
Description
COUNTER 11-PIN 12VDC 4DIGIT SPDT
Manufacturer
Omron
Series
H7CXr
Datasheet
1.H7CX-AS_AC100-240.pdf
(63 pages)
Specifications of H7CX-A114D1 DC12-24/AC24
Count Rate
*
Number Of Digits/alpha
6
Input Type
*
Output Type
*
Voltage - Supply
12 V ~ 24 VDC, 24VAC
Display Type
*
No. Of Digits / Alpha
4
Meter Function
Counter
Signal Input Type
PNP/NPN
Supply Voltage Max
24VDC
Character Size
11.5mm
Ip/nema Rating
IP66 / NEMA 4
Panel Cutout Height
45mm
Supply Voltage Min
12VDC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
H7CX-A114D1DC12-24/AC24
H7CXA114D1DC1224AC24
H7CXA114D1DC1224AC24
■ Operating Procedures (Tachometer Function)
Switching from Counter to Tachometer
Settings for Basic Operations
Note: 1. Be sure to set pin 1 of the DIP switch to ON. If it is set to OFF, the DIP switch settings will not be enabled.
The H7CX is factory-set to the 2-stage
counter (1-stage counter for H7CX-AU@
models) configuration. To switch to the
tachometer configuration, use the
procedure shown on the right. For details,
refer to page 36.
1
2
3
4
5
6
7
8
Settings for basic functions can be performed with just the DIP switch.
Easy Confirmation of Switch Settings Using Indicators
Advanced-Function Settings
After making DIP switch settings for basic operations, advanced-functions (see note) can be added using the operation keys.
For details, refer to page 31.
Note: Advanced functions consist of decimal point position, prescale value, auto-zero time, startup time, display color, output
The ON/OFF status of the DIP switch pins can be
confirmed using the front display. For details, refer to page 36.
2. Changes to DIP switch settings are enabled when the power is turned ON.
DIP switch set-
tings enable/
disable
Counting speed 30 Hz
Tachometer out-
put mode
Average pro-
cessing
Not used
NPN/PNP input
mode
allocation, and key protect level.
Item
Disabled
Refer to the table on the right.
Refer to the table on the right.
---
NPN
OFF
Note: All of the pins are factory-set to OFF.
OFF
ON
Enabled
10 kHz
---
PNP
1
Be sure to set pin 1 to ON.
Switch to 2cnt to taco (tachometer operation) using the
ON
2
Configuration selection mode
3
4
5
6
Note: The
7
8
MODE
+
MODE
1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
key must be pressed before the
Hold down for
1 s min. (See note.)
Pin 3
Pin 5
OFF
OFF
ON
ON
OFF
OFF
ON
ON
Pin 4
Pin 6
key.
Power ON
Run mode
Area
Upper limit
Lower limit
Upper and lower limit
OFF (no average processing)
2 times
4 times
8 times
Tachometer output mode
Average processing
1
key.
H7CX-A
30