H7CX-A-N AC100-240 Omron, H7CX-A-N AC100-240 Datasheet - Page 35
![COUNTER DGTL SPDT 100-240VAC](/photos/6/44/64478/h7cx-a-n_ac100-240_sml.jpg)
H7CX-A-N AC100-240
Manufacturer Part Number
H7CX-A-N AC100-240
Description
COUNTER DGTL SPDT 100-240VAC
Manufacturer
Omron
Type
1 Stage and Total Preset Counterr
Specifications of H7CX-A-N AC100-240
Count Rate
30Hz or 5kHz Selectable
Number Of Digits/alpha
6
Input Type
Voltage, Switch Closure, Transistor Switch
Output Type
Switch Closure
Voltage - Supply
100 V ~ 240 VAC
Display Type
LCD Backlit
Frequency Response
50 Hz
Product
Panel Mount Tachometer
Voltage
100 VAC to 240 VAC
Accuracy
+/- 0.1 %
No. Of Digits / Alpha
6
Digit Height
10mm
Power Consumption
9.4VA
Counting Speed
5kHz
Operating Temperature Range
-10°C To +55°C
Character Size
9mm
Supply Voltage Min
100VAC
Panel Cutout Width
45mm
Meter Function
Counter
Rohs Compliant
Yes
Connector Type
Screw Terminal
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
H7CXANAC100240
Z3040
Z3040
Switching between Preset Counter, Total and Preset Counter, Batch Counter, Dual
Counter, Twin Counter, and Tachometer Operation
Select which H7CX configuration is used (i.e., preset counter, total and preset counter, batch counter, dual counter, twin counter, or tachometer)
in configuration selection mode.
The H7CX is also equipped with a DIP switch monitor function, a convenient function that enables the settings of the DIP switch pins to be
confirmed using the display on the front of the H7CX.
Hold Function
The measurement value (display value) and output are sustained while the hold input is ON.
Note: The output will maintain the current status when the hold key is pressed.
Example:
*1 When the mode is changed to configuration selection mode, the present value is reset, outputs turn OFF, and counting (measuring) stops.
*2 Setting changes made in configuration selection mode are enabled when the mode is changed to run mode. If the configuration is changed, the
set value (or set value 1 and set value 2), comparison value 1 and comparison value 2 are initialized.
Output mode
Lower limit
setting
*2
Comparison value (lower limit)
Power ON
key for 1 s
Press the
Hold input* (Reset Key)
min.
+
1
Display value
*1
Configuration
selection
DIP switch
monitor
(DIP)
OUT
Operation
Note
Select the configuration using the UD Key.
*The configurations that can be selected depend on the model.
Note: By default, the H7CX is set to the 1-stage preset counter configuration. (Two-stage
Confirm the status of DIP switch pins 1 to 8 using the UD Key.
*This display is possible only when DIP switch pin 1 (DIP switch settings enable/disable)
To change the mode to configuration selection mode, hold
down the
The mode will not change if the
is set to ON (enable).
OFF
ON
1cnt
(1-stage
preset
counter)
Key
Example
models are set to the 2-stage preset counter configuration.)
1 2 3 4 5 6 7 8
Actual input
1
2cnt
(2-stage
preset
counter)
Key for 1 s min. with the
Sustained output
Sustained display value
(Total and
preset counter)
tcnt
1
Key
Key is pressed first.
(Batch
counter)
bcnt
1
Key
Key held down.
…Indicates that DIP switch pin 8 is ON.
…Indicates that DIP switch pin 7 is OFF.
…Indicates that DIP switch pin 6 is ON.
…Indicates that DIP switch pin 5 is OFF.
…Indicates that DIP switch pin 4 is ON.
…Indicates that DIP switch pin 3 is OFF.
…Indicates that DIP switch pin 2 is ON.
…Indicates that DIP switch pin 1 is ON.
dcnt
(Dual
counter)
RST
H7CX-A@-N
(Twin
counter)
twn
(Tachometer)
taco
Key
1
35