ML610Q407-NNNTBZ03A7 Rohm Semiconductor, ML610Q407-NNNTBZ03A7 Datasheet
ML610Q407-NNNTBZ03A7
Specifications of ML610Q407-NNNTBZ03A7
Available stocks
Related parts for ML610Q407-NNNTBZ03A7
ML610Q407-NNNTBZ03A7 Summary of contents
Page 1
... Microcontroller with a Built-in LCD driver GENERAL DESCRIPTION ML610Q407/ML610Q408/ML610Q409 is a high-performance 8-bit CMOS microcontroller into which peripheral circuits, such as synchronous serial port, UART, melody driver, RC oscillation type A/D converter, and LCD driver, are incorporated around OKI Semiconductor-original 8-bit CPU nX-U8/100. ML610Q407/ML610Q408/ML610Q409 operates in both high/low-speed mode and power-saving mode most suitable for battery operated products ...
Page 2
... LCD driver − The number of segments ML610Q407: 145 dots max. (29seg×5com, 30seg×4com, 31seg×3com, and 32seg×2com selectable) ML610Q408: 165 dots max. (33seg×5com, 34seg×4com, 35seg×3com, and 36seg×2com selectable) ML610Q409: 185 dots max. (37seg×5com, 38seg×4com, 39seg×3com, and 40seg×2com selectable) − ...
Page 3
... ROM code number (xxx is NNN for blank product) Q: MTP version P: Wide range temperature version WA: Chip TBZ03A: TQFP • Guaranteed operating range − Operating temperature: −20°C to +70°C (P version: −40°C to +85°C) − Operating voltage 1.25V to 3.6V DD FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 3/33 ...
Page 4
... OKI SEMICONDUCTOR ML610Q407/ML610Q408/ML610Q409 Block Diagram Figure 1 show the block diagram of the ML610Q407/ML610Q408/ML610Q409. "*" indicates the secondary function of each port. (*1) " "： 29seg×5com, 30seg×4com, 31seg×3com, and 32seg×2com selectable (*2) " "： 33seg×5com, 34seg×4com, 35seg×3com, and 36seg×2com selectable (*3) " ...
Page 5
... P32 90 P33 91 P35 92 P57 93 P56 94 P55 95 P54 96 P53 (NC) 99 (NC) 100 Note: The assignment of the P30 to P35 are not in order. Figure 2 ML610Q407 TQFP100 Pin Configuration FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 50 (NC) (NC) 49 SEG17 48 47 SEG16 SEG15 46 45 SEG14 SEG13 44 SEG12 43 42 SEG11 41 SEG10 SEG9 40 SEG8 ...
Page 6
... P33 91 P35 92 P57 93 P56 94 P55 95 P54 96 P53 (NC) 99 (NC) 100 Note: The assignment of the P30 to P35 are not in order. Figure 3 ML610Q408 TQFP100 Pin Configuration FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 50 (NC) 49 (NC) SEG17 48 47 SEG16 SEG15 46 45 SEG14 SEG13 44 SEG12 43 42 SEG11 41 SEG10 40 SEG9 SEG8 39 38 ...
Page 7
... P33 91 P35 92 P57 93 P56 94 P55 95 P54 96 P53 (NC) 99 (NC) 100 Note: The assignment of the P30 to P35 are not in order. Figure 4 ML610Q409 TQFP100 Pin Configuration FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 50 (NC) (NC) 49 SEG17 48 SEG16 47 SEG15 46 45 SEG14 44 SEG13 SEG12 43 42 SEG11 41 SEG10 SEG9 40 SEG8 39 38 SEG7 ...
Page 8
... The assignment of the pads P30 to P35 are not in order. 2.27mm Chip size: 2.27 mm × 2.23 mm PAD count: 88 pins Minimum PAD pitch: 80μm PAD aperture: 70μm×70μm Chip thickness: 350μm Voltage of the rear side of chip: V Figure 5 ML610Q407 Chip Layout & Dimension FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 SEG17 44 SEG16 43 SEG15 ...
Page 9
... The assignment of the pads P30 to P35 are not in order. 2.27mm Chip size: 2.27 mm × 2.23 mm PAD count: 88 pins Minimum PAD pitch: 80μm PAD aperture: 70μm×70μm Chip thickness: 350μm Voltage of the rear side of chip: V Figure 6 ML610Q408 Chip Layout & Dimension FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 44 SEG17 43 SEG16 SEG15 42 SEG14 41 40 ...
Page 10
... The assignment of the pads P30 to P35 are not in order. 2.27mm Chip size: 2.27 mm × 2.23 mm PAD count: 88 pins Minimum PAD pitch: 80 μm PAD aperture: 70 μm×70 μm Chip thickness: 350 μm Voltage of the rear side of chip: V Figure 7 ML610Q409 Chip Layout & Dimension FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 44 SEG17 43 SEG16 SEG15 42 SEG14 41 40 ...
Page 11
... OKI SEMICONDUCTOR ML610Q407/ML610Q408/ML610Q409 Pad Coordinates Table 1 ML610Q407/ML610Q408/ML610Q409 Pad Coordinates PAD Pad No. Name X (μm) -853 1 P52 -773 2 P51 -693 3 P50 -613 4 P40 -533 5 P41 -453 6 P42 -373 7 P43 -293 8 P44 -213 9 P45 -133 10 P46 11 P47 12 VDD 107 13 VSS 187 14 VDDL 267 15 XT0 ...
Page 12
... Secondary Output port Secondary Input/output port Secondary Input/output port Secondary Input/output port Secondary Input/output port Secondary Input/output port Secondary Input/output port Secondary ML610Q407/ML610Q408/ML610Q409 Secondary function or Tertiary function Pin name I/O Function ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ...
Page 13
... Secondary Secondary Tertiary Secondary Tertiary Secondary Tertiary SOUT1 ⎯ Secondary Tertiary Secondary Tertiary Secondary Tertiary SOUT1 ⎯ FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 I/O Function ⎯ ⎯ ⎯ SIN0 I SSIO0 data input ⎯ ⎯ ⎯ SSIO0 synchronous clock SCK0 I/O input/output RXD0 I UART data input ...
Page 14
... (*5) SEG39 Internally generated, or connect to either positive power supply pin ( For details, see "Chapter 22 LCD Drivers. in the user’s manual" DDL Pin for ML610Q407/ML610Q408 Pin for ML610Q409 Pin for ML610Q407 Pin for ML610Q408/ML610Q409. Secondary/ Function Tertiary LCD common pin LCD common pin ...
Page 15
... Since these pins have secondary functions, the pins cannot be used as a port when the secondary functions are used. General-purpose input/output port. P60-P63 O These pins are for the ML610Q407/ ML610Q408, but are not provided in the ML610Q409. General-purpose input/output port. P64-P67 O These pins are for the ML610Q407, but are not provided in the ML610Q409 ...
Page 16
... P45 pin. Melody Melody/Buzzer signal output pin. This pin is used as the secondary MD0 O function of the P22 pin and P50 pin. LED drive Nch open drain output pins to drive LED. LED0-2,4 O ML610Q407/ML610Q408/ML610Q409 Description FEDL610Q409-01 Primary/ Secondary/ Logic Tertiary Secondary Positive Primary/ ...
Page 17
... Segment output pins. SEG0-31 O Segment output pin. These pins are for the ML610Q408/ML610Q409, but SEG32-35 O are not provided in the ML610Q407. Segment output pin. These pins are for the ML610Q409, but are not SEG36-39 O provided in the ML610Q407/ML610Q408. LCD driver power supply Power supply pins for LCD bias (internally generated or V — ...
Page 18
... It is recommended to set the unused input ports and input/output ports to the inputs with pull-down resistors/pull-up resistors or the output mode since the supply current may become excessively large if the pins are left open in the high impedance input setting. Table 2 Termination of Unused Pins Recommended pin termination FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Open Open Open Open Open ...
Page 19
... 30k to 2.5MHz 1. 1.8 to 3.6V DD ⎯ f XTL ⎯ ⎯ ⎯ ⎯ ⎯ FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 (V = 0V) SS Rating Unit −0.3 to +4.6 V −0.3 to +9.5 V −0.3 to +3.6 V −0.3 to +2.0 V −0.3 to +4.0 V −0.3 to +6.0 V −0 +0 −0 +0 −12 to +11 mA −12 to +20 mA 0.9 W −55 to +150 °C ...
Page 20
... T STOP ⎯ P RST ⎯ P NRST ⎯ T POR VIL1 VIL1 P RST RESET_N pin reset 0.9xV DD T POR Power on reset FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Range 0 to +40 *1 2.75 to 3.6 *1 2.5 to 2.75 *1 7 Rating Unit Min. Typ. Max. Typ. Typ. 500 −10% +10% kHz Typ. ...
Page 21
... Ta = −20 to +70° −40 to +85°C for P version, unless otherwise specified) SS Condition f = 30k to 625kHz 30k to 2.5MHz 3.0V DD ⎯ becomes V level when the V DDL DD level. DD FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Rating Unit Min. Typ. Max. 1.1 1.2 1.3 1.35 1.5 1.65 ⎯ ⎯ -1 mV/°C ⎯ mV/V ...
Page 22
... Ta = −20 to +70° −40 to +85°C for P version 3.0V Condition Ta= 25° Ta= 25° Ta= 25° Ta= 25° Ta= 25° FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Rating Measuring Unit circuit Min. Typ. Max. ⎯ 0.4 0.8 μA ⎯ ⎯ 8 ⎯ 0.9 1.8 μA ⎯ ⎯ 9 ⎯ μA ⎯ ⎯ 15 ⎯ 70 100 μ ...
Page 23
... IIL2 IIH3 Input current 3 (P00-P04) (P30-P35) IIL3 (P40-P47) (P50-P57) IIH3Z VIH3 = V IIL3Z VIL3 = pins for ML610Q407 pins for ML610Q408 pins for ML610Q409 = 0V −20 to +70° −40 to +85°C for P version, unless otherwise specified) SS Condition IOH1 = −0.5mA 1 1.25 to 3.6V DD IOL1 = +0 ...
Page 24
... Ta = −20 to +70° −40 to +85°C for P version, unless otherwise specified) SS Condition ⎯ 1 1. 10kHz V = 50mV rms Ta = 25°C FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Rating Unit Min. Typ. Max. 0.7 ⎯ × 0.3 ⎯ 0 ×V DD 0.2 ⎯ ...
Page 25
... XT1 MEASURING CIRCUIT 2 VIH (*1) VIL DDL DDL (*1) Input logic circuit to determine the specified measuring conditions. (*2) Measured at the specified output pins. FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 1μ 0.47μ 0.1μ 0.47μF 12 32.768kHz crystal: DT-26 (Load capacitance 6pF) (made by KDS:DAISHINKU CORP 6pF 25/33 ...
Page 26
... VIH RS1 VIL V MEASURING CIRCUIT 4 (* MEASURING CIRCUIT 5 VIH (*1) VIL DDL *1: Input logic circuit to determine the specified measuring conditions. *2: Measured at the specified output pins DDL *3: Measured at the specified output pins DDL *1: Input logic circuit to determine the specified measuring conditions. FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 (* 26/33 ...
Page 27
... NUL t NUL t NUL = 0V −20 to +70° −40 to +85°C for P version, unless otherwise specified) SS Symbol Condition ⎯ t TBRT ⎯ t RBRT t TBRT t RBRT FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Rating Unit Min. Typ. Max. ⎯ 76.8 106.8 Rating Unit Min. Typ. Max. 1 ⎯ ⎯ BRT BRT* ...
Page 28
... When RC oscillation is 2MHz 1.8 to 3.6V) DD When RC oscillation is 500kHz 1.25 to 3.6V When RC oscillation is 2MHz 1.8 to 3.6V SCYC FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Rating Min. Typ. Max. ⎯ ⎯ 10 ⎯ ⎯ ⎯ ⎯ SCLKn* ⎯ ⎯ 4 ⎯ ⎯ SCLKn* SCLKn* SCLKn* ×0.4 ×0.5 ×0.6 ⎯ ⎯ 500 ⎯ ...
Page 29
... OSCX , f (RS0-CS0 oscillation) OSCX CVR0 CVR1 IN1 CS1 RS1 RT1 RT0 RCT0 RS0 V DDL C L *1: Input logic circuit to determine the specified measuring conditions. ML610Q407/ML610Q408/ML610Q409 Rating Min. Typ. Max. 1 ― 457.3 525.2 575.1 53.48 58.18 62.43 5.43 5.89 6.32 7.972 9.028 9 ...
Page 30
... OSCX CVR0 CVR1 RCT0 RS0 RT0 IN1 CS1 RS1 RT1 V DD DDL C L *1: Input logic circuit to determine the specified measuring conditions. FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Rating Min. Typ. Max. 1 ― ― 81.93 93.16 101.2 35.32 38.75 41.48 5.22 5.65 6.03 2.139 2 ...
Page 31
... The surface mount type packages are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact our responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times). FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 (Unit: mm) Package material Epoxy resin ...
Page 32
... OKI SEMICONDUCTOR REVISION HISTORY Document No. Date FEDL610Q409-01 Nov.7,2010 Page Previous Current Edition Edition – – Formally edition 1 FEDL610Q409-01 ML610Q407/ML610Q408/ML610Q409 Description 32/33 ...
Page 33
... No part of the contents contained herein may be reprinted or reproduced without our prior permission. ML610Q407/ML610Q408/ML610Q409 Copyright 2010 OKI SEMICONDUCTOR CO., LTD. FEDL610Q409-01 ...