DS92LV1260TUJBX National Semiconductor, DS92LV1260TUJBX Datasheet - Page 11
![](/photos/31/46/314653/196pin_lbga_sml.jpg)
DS92LV1260TUJBX
Manufacturer Part Number
DS92LV1260TUJBX
Description
Manufacturer
National Semiconductor
Datasheet
1.DS92LV1260TUJBX.pdf
(17 pages)
Specifications of DS92LV1260TUJBX
Number Of Elements
6
Input Type
CMOS/TTL
Operating Supply Voltage (typ)
3.3V
Differential Input High Threshold Voltage
50mV
Diff. Input Low Threshold Volt
-50mV
Output Type
Deserializer
Transmission Data Rate
400Mbps
Power Dissipation
3.7W
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
196
Number Of Receivers
1
Number Of Drivers
10
Lead Free Status / RoHS Status
Not Compliant
Application Information
• Use at least 4 PCB board layers (Bus LVDS signals,
• Keep Serializers and Deserializers as close to the (Bus
• Bypass each Bus LVDS device and also use distributed
ground, power, and TTL signals).
Power system performance may be greatly improved by
using thin dielectrics (4 to 10 mils) for power/ground
sandwiches. This increases the intrinsic capacitance of
the PCB power system which improves power supply
filtering, especially at high frequencies, and makes the
value and placement of external bypass capacitors less
critical.
LVDS port side) connector as possible.
Longer stubs lower the impedance of the bus, increase
the load on the Serializer, and lower the threshold margin
at the Deserializers. Deserializer devices should be
placed much less than one inch from slot connectors.
Because transition times are very fast on the Serializer
Bus LVDS outputs, reducing stub lengths as much as
possible is the best method to ensure signal integrity.
bulk capacitance between power planes.
Surface mount capacitors placed close to power and
ground pins work best. External bypass capacitors
should include both RF ceramic and tantalum electrolytic
types. RF capacitors may use values in the range 0.001
µF to 0.1 µF. Tantalum capacitors may be in the range 2.2
µF to 10 µF. Voltage rating for tantalum capacitors should
be at least 5X the power supply voltage being used.
Randomly distributed by-pass capacitors should also be
used.
Package and pin layout permitting, it is also recom-
mended to use two vias at each power pin as well as all
RF bypass capacitor terminals. Dual vias reduce the
interconnect inductance between layers by up to half,
thereby reducing interconnect inductance and extending
the effective frequency range of the bypass components.
The outer layers of the PCB may be flooded with addi-
tional ground planes. These planes will improve shielding
and isolation as well as increase the intrinsic capacitance
of the power supply plane system. Naturally, to be effec-
(Continued)
11
For a typical application circuit, please see Figure 8.
There are more common practices which should be followed
when designing PCBs for LVDS signaling. General applica-
tion guidelines and hints may be found in the following
application notes: AN-808, AN-903, AN-971, AN-977, and
AN-1108. For packaging information on BGA’s, please see
AN-1126.
USING T
QUALITY
The parameter t
much of the ideal bit the receiver needs to ensure correct
sampling. After determining this amount, what remains of the
ideal bit that is available for external sources of noise is
called t
The vertical limits of the mask are determined by the
DS92LV1260 receiver input threshold of +/− 50mV.
Please refer to the eye mask pattern of Figure 10 for a
graphic representation of t
• Use a termination resistor which best matches the differ-
• Leave unused Bus LVDS receiver inputs open (floating).
• Isolate TTL signals from Bus LVDS signals.
• Use controlled impedance media.
tive, these planes must be tied to the ground supply
plane at frequent intervals with vias. Frequent via place-
ment improves signal integrity on signal transmission
lines by providing short paths for image currents, which
reduces signal distortion. Depending on which is greater,
the planes should be pulled back from all transmission
lines and component mounting pads a distance equal to
the width of the widest transmission line or the thickness
of the dielectric separating the transmission line from the
internal power or ground plane(s). Doing so minimizes
effects on transmission line impedances and reduces
unwanted parasitic capacitances at component mounting
pads.
ential impedance of your transmission line.
Limit traces on unused inputs to
The backplane and connectors should have a matched
differential impedance.
RNM
DJIT
.
AND T
RNM
RNM
is calculated by first measuring how
TO VALIDATE SIGNAL
DJIT
and t
RNM
<
0.5 inches.
.
www.national.com