CAT5409YI-10-TE13 ON Semiconductor, CAT5409YI-10-TE13 Datasheet - Page 3

• Manufacturer Part Number: CAT5409YI-10-TE13
• Manufacturer: ON Semiconductor

Specifications of CAT5409YI-10-TE13

• Number Of Elements: 4
• # Of Taps: 64
• Resistance (max): 10KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (2-Wire/I2C)
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 6V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Lead Free Status / RoHS Status: Compliant

ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING CONDITIONS
POTENTIOMETER CHARACTERISTICS
Over recommended operating conditions unless otherwise stated.
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
(2) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC
(3) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to V
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.
(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentio-
(7) LSB = R
(8) n = 0, 1, 2, ..., 63
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
Parameters
Temperature Under Bias
Storage Temperature
Voltage on Any Pin with Respect to V
V
Package Power Dissipation Capability (T
Lead Soldering Temperature (10 s)
Wiper Current
Parameters
V
Industrial Temperature
C
Symbol
TC
TC
CC
CC
H
V
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
voltage on output pins is V
meter. It is a measure of the error in step size.
R
R
R
R
/C
R
R
TERM
I
fc
POT
POT
POT
POT
RATIO
with Respect to Ground
RPOT
W
W
W
L
/C
W
TOT
/ 63 or (R
Parameter
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Potentiometer Resistance (-2.5)
Potentiometer Resistance
Tolerance
R
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
Resolution
Absolute Linearity
Relative Linearity
Temperature Coefficient of R
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
POT
Matching
H
- R
L
CC
) / 63, single pot.
+0.5 V, which may overshoot to V
H
(6)
(5)
or R
L
Pin
SS
POT
(1) (2)
(1)
A
= 25ºC)
Test Conditions
25°C, each pot
I
I
V
R
R
(4)
(4)
(4)
R
W
W
SS
W(n)(actual)
W(n+1)
POT
= ±3 mA @ V
= ±3 mA @ V
= 0 V
= 50 kΩ
- [R
CC
- R
+2.0 V for periods of less than 20 ns.
W(n) + LSB
3
(n)(expected)
(4)
CC
CC
]
(8)
= 3 V
= 5 V
(8)
GND
Min
-2.0 to +V
CC
+1 V.
-55 to +125
-65 to +150
-2.0 to +7.0
+2.5 to +6
-40 to +85
Ratings
Ratings
10/10/25
300
±12
±300
1.0
Typ
100
2.5
1.6
0.4
50
10
80
CC
+ 2.0
Max
Doc. No. MD-2010 Rev. M
±0.2
±20
300
150
V
50
±6
±1
20
1
CC
CAT5409
ppm/ºC
ppm/ºC
Units
Units
LSB
LSB
Units
MHz
mA
mW
ºC
°C
ºC
°C
mA
W
kΩ
kΩ
kΩ
kΩ
pF
V
V
V
%
%
%
Ω
Ω
V
(7)
(7)