LXMG1618-05-21 MICROSEMI, LXMG1618-05-21 Datasheet - Page 2

• Manufacturer Part Number: LXMG1618-05-21
• Manufacturer: MICROSEMI

Specifications of LXMG1618-05-21

• Operating Temperature Classification: Commercial
• Pin Count: 10
• Lead Free Status / RoHS Status: Compliant

Copyright © 2002
Rev. 1.0a,2006-11-13
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
Input Signal Voltage (V
Input Power ...................................................................................................................................................................... 3.0W
Output Voltage, no load ............................................................................................................ Internally Limited to 1300V
Output Current ............................................................................................................................6.5mA
Output Power ................................................................................................................................................................... 2.3W
Input Signal Voltage ( SLEEP Input) ....................................................................................................................-0.3V to 5.5V
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
Output Power
Linear BRITE Control Input Voltage Range¹
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current
Full Bright Lamp Current
Full Bright Lamp Current
Full Bright Lamp Current
Min. Average Lamp Current
Lamp Start Voltage
Operating Frequency
¹The minimum V
* Total output power must not exceed 4W. Higher voltage lamps may require maximum output current to be set lower than 5mA
brightness (BRITE) input at or above the panel specification for minimum current.
* The inverter is capable of a lower output current than may be recommended by the panel manufacturer. It is the user’s responsibility to set the minimum
TM
terminal.
Parameter
BRT ADJ
Parameter
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: [phone]
voltage depends on the panel characteristics, depending on the panel it can vary from 0.65V to 0.9V
IN1
R E C O M M E N D E D O P E R A T I N G C O N D I T I O N S ( R . C . )
)....................................................................................................................................-0.3V to 6.5V
A B S O L U T E M A X I M U M R A T I N G S
E L E C T R I C A L C H A R A C T E R I S T I C S
Symbol
I
I
I
I
I
L(MAX)
L(MAX)
L(MAX)
L(MAX)
L(MIN)
V
f
LS
O
V
I
V
I
V
I
V
I
V
I
-20°C < T
V
SET1
SET1
SET1
SET1
SET1
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
Integrated Products
®
= Ground, I
= Ground, I
= Open, I
= Open, I
= I
Microsemi
Symbol
SET2
V
> 2.0V
> 2.0V
> 2.0V
> 2.0V
=0.65V
= 2.5V
V
I
BRT_ADJ
OLAMP
PanelMatch™
V
A
P
LAMP
T
< 70°C, V
IN1
= Ground
O
A
SET2
SET2
DC
DC
DC
DC
DC
DC
Test Conditions
SET2
SET2
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
= Ground
= Open
= Ground
= Open
IN1
5V 2.2W CCFL Programmable Inverter Module
Recommended Operating Conditions
0.65 to 0.9
> 4.5V
4.75
Min
325
4.5
3.5
-20
DC
P
RODUCTION
IN1
IN1
IN1
IN1
IN1
IN1
( N O T E 1 )
= 5V
= 5V
= 5V
= 5V
= 5V
= 5V
R.C.
380
DC
DC
DC
DC
DC
5
5
D
ATASHEET
1000
Min
3.0
3.5
4.0
4.5
85
LXMG1618-05-2x
Max
435*
5.25
5.5
2.2
2.0
5.0
RMS
LXMG1618-05-2x
70
1100
Typ
1.5*
(Internally Limited)
3.5
4.0
4.5
90
5
Max
4.0
4.5
5.0
5.5
94
mA
Units
RMS
V
°C
W
RMS
V
V
RMS
RMS
Units
mA
mA
mA
mA
mA
V
kHz
RMS
Page 2
RMS
RMS
RMS
RMS
RMS