FLTR100V20 Lineage Power, FLTR100V20 Datasheet
FLTR100V20
Specifications of FLTR100V20
Available stocks
Related parts for FLTR100V20
FLTR100V20 Summary of contents
Page 1
... Computer equipment n Description The FLTR100V20 Filter Module is designed to reduce the conducted common-mode and differential-mode noise on input or output lines of high-frequency switching power supplies. The module has a maximum current rating provides high insertion loss throughout the frequency range regulated by the U.S. Federal Communications Commission (FCC) and the International Special Committee on Radio Interference (CISPR) for conducted emissions ...
Page 2
... Input Voltage: Continuous Transient (100 ms) Voltage from GND to Either Input Lead (1 minute) Operating Case Temperature Storage Temperature 2 Symbol Min Max V — — 100 I, trans — — 2500 T –40 100 C T –55 125 stg March 2008 Unit Vdc V Vdc °C °C Lineage Power ...
Page 3
... Resistance per Leg Maximum Average Current ( °C): A 2.03 m/s (400 lfm) air Natural convection Common-mode Insertion Loss (50 Ω circuit, 500 kHz) Differential-mode Insertion Loss (50 Ω circuit, 500 kHz) Lineage Power 75 Vdc Input Maximum Maximum Symbol Min Typ R — — I — — ...
Page 4
... Must Be Kept Below 100 °C) 0 -20 -40 -60 -80 -100 0.1 1.0 FREQUENCY (MHz) Figure 2. Typical Common-Mode Insertion Loss ¾ Circuit -20 -40 -60 - -100 0.1 8-1322a Figure 3. Typical Differential-Mode Insertion Loss 10 30 8-1326a March 2008 1.0 FREQUENCY (MHz ¾ Circuit Lineage Power 10 30 8-1327a ...
Page 5
... The shield plane should be connected to the CASE pin. Lineage Power 75 Vdc Input Maximum Maximum GND Figure 4. Internal Schematic The GND pin of the filter module is attached to Y caps within the module ...
Page 6
... Figure 6. Recommended Layout When Used as the Input Filter to a High-Frequency dc-to-dc Converter 6 V (+) I C5 POWER MODULE V (-) SHIELD PLANE C1 FILTER MODULE V (+) I C5 CASE V (-) March 2008 V (+) O V (-) O CASE C3 POWER MODULE C4 SHIELD PLANE C3 (+) and V (–) planes, as should the V (+) and Lineage Power 8-1325d V (+) O V (-) O 8-1328f (–) O ...
Page 7
... Note: C1 through C4 and C6 through C9 can be 0.01 µF to 0.1 µF. Select the voltage rating to meet input-to-output isolation requirements. C5 should be the recommended value indicated in the power module data sheet. Figure 7. Recommended Schematic of Filter Module with Two Power Modules Lineage Power 75 Vdc Input Maximum Maximum V ...
Page 8
... It is often useful to make a model of the power card, using copper tape and a vector card, to experiment with various layout and grounding approaches prior to committing to a printed-wiring board. March 2008 Lineage Power ...
Page 9
... Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.). Top View Side View 0.51 (0.020) Bottom View (0.15) 3.8 (0.15) 5.08 (0.200) 5.08 (0.200) 5.08 (0.200) Lineage Power 75 Vdc Input Maximum Maximum 50.8 (2.00) MAX FLTR100V20 40.6 Filter Module (1.60) MAX V = 75Vdc Max 20Adc Max GND 1.02 (0.040) DIA ROUND PIN (TYP) 17 ...
Page 10
... Component-side footprint. Dimensions are in millimeters and (inches). Note: Do not route copper paths beneath power module standoffs. 5.08 (0.200) 5.08 (0.200) 5.08 (0.200) 3.8 (0.15) (0.15) Ordering Information Device Code FLTR100V20 107742454 FLTR100V206 108995775 10 MODULE OUTLINE V I GND 25.4 (1.000) 3.8 17.78 (0.700) ...
Page 11
... Lineage Power Board Mounted Power Modules:Soldering and Cleaning Application Note. Through-Hole Lead Free Soldering Infor- mation ...
Page 12
... Vdc Input Maximum Maximum Ordering Information Device Code FLTR100V20 107742454 FLTR100V206 108995775 FLTR100V20Z CC109103248 FLTR100V206Z CC109103256 World W ide Headq u arters Lineag e Power Corporation 30 00 Skyline D rive, Mesquite 75149 World Wide Headquarters Tyco Electronics Power Systems, Inc. +1-800-526-7819 (Outsid e U .S.A .: +1- 97 2-2 84 -2626) ...