PEEL22CV10AZJ-25L Diodes Zetex, PEEL22CV10AZJ-25L Datasheet - Page 8

• Manufacturer Part Number: PEEL22CV10AZJ-25L
• Manufacturer: Diodes Zetex

Specifications of PEEL22CV10AZJ-25L

• Process Technology: EECMOS
• # Macrocells: 10
• # I/os (max): 10
• Propagation Delay Time: 25ns
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 28
• Lead Free Status / RoHS Status: Compliant

Anachip Corp.
www.anachip.com.tw
Table 10.
Switching Waveforms
Notes:
1. Minimum DC input is -0.5V, however, inputs may undershoot to -2.0V for peri-
ods less than 20 ns.
2. V
3. Test Points for Clock and VCC in t
levels.
4. I/O pins are 0V and V
5. “Input” refers to an input pin signal.
6. t
input transition to V
7. Capacitances are tested on a sample basis.
Symbol
OE
t
I
CL
t
f
f
f
RESET
and V
t
t
MAX1
MAX2
MAX3
t
t
t
t
t
t
t
t
t
t
CO1
CO2
is measured from input transition to V
AW
OD
PD
OE
CF
SC
HC
, t
CP
AP
AR
CH
Registered Feedback,
Synchronous Preset
O
are not specified for program/verify operation.
Input
Input
Input
Clock to Output
Clock to comb. Output delay via internal registered feedback
Clock to Feedback
Input
Input
Clock low time, clock high time
Min clock period Ext (t
Internal feedback (1/t
External feedback (1/t
No feedback (1/t
Asynchronous Reset Pulse Width
Input to Asynchronous Reset
Asynchronous Reset recovery time
Power-on reset time for registers in clear state
Asynchronous
Combinatorial
OH
Inputs, I/O,
-0.1V or V
Registered
5
5
5
5
5
CC
to non-registered output
to output enable
to output disable
or feedback setup to clock
hold after clock
Outputs
Outputs
.
Reset
Clock
OL
available, contact Customer Service
+0.1V; V
R
CL
and t
Over the operating range
+t
contact factory for availability
CH
F
REF
SC
CP
are referenced at the 10% and 90%
REF
6
)
6
SC
+ t
)
11
±0.1V, T
11
=V
+ t
CF
L.
CO1
)
11
Parameter
OD
)
8
is measured from
8
12
8/10
8. Test conditions assume: signal transition times of 3ns or less from the 10% and
90% points, timing reference levels of 1.5V (Unless otherwise specified).
9. Test one output at a time for a duration of less than 1 second.
10. I
grammed as a 10-bit Counter.
11. Parameters are not 100% tested. Specifications are based on initial character-
ization and are tested after any design process modification that might affect oper-
ational frequency.
12. All inputs at GND.
CC
for a typical application: This parameter is tested with the device pro-
Min
41.6
33.3
38.4
13
30
15
25
0
-25
Max
25
25
25
15
35
25
25
9
5
Rev. 1.0 Dec 16, 2004
Unit
MHz
MHz
MHz
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns