5962-9759801QXC QP SEMICONDUCTOR, 5962-9759801QXC Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/5/550/qp_semiconductor_sml.jpg)
5962-9759801QXC
Manufacturer Part Number
5962-9759801QXC
Description
Manufacturer
QP SEMICONDUCTOR
Datasheet
1.5962-9759801QXC.pdf
(21 pages)
Specifications of 5962-9759801QXC
Lead Free Status / RoHS Status
Supplier Unconfirmed
DSCC FORM 2234
APR 97
(see 3.5 herein).
before and after the required burn-in screens and steady-state life tests to determine delta compliance. The electrical
parameters to be measured, with associated delta limits are listed in table IIB. The device manufacturer may, at his option,
either perform delta measurements or within 24 hours after life test perform final electrical parameter tests, subgroups 1, 7, and
9.
upon request.
made available upon request.
Q and V or MIL-PRF-38535, appendix A for device class M.
(original equipment), design applications, and logistics purposes.
prepared specification or drawing.
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users
and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic
devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544.
(614) 692-0547.
MIL-PRF-38535 and MIL-HDBK-1331.
The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to
this drawing.
The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DSCC-VA.
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
4.5 Delta measurements for device class V. Delta measurements, as specified in table IIA, shall be made and recorded
4.6 Erasure procedures. Erasure procedures shall be as specified by the device manufacturer and shall be made available
4.7 Programming procedures. The programming procedures shall be as specified by the device manufacturer and shall be
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus (DSCC) when a system
6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43218-3990, or telephone
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.
6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103.
a.
b.
c.
DEFENSE SUPPLY CENTER COLUMBUS
End-point electrical parameters shall be as specified in table IIA herein.
For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as
specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to
radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device
classes must meet the postirradiation end-point electrical parameter limits as defined in table I at T
after exposure, to the subgroups specified in table IIA herein.
When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied.
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
STANDARD
SIZE
A
REVISION LEVEL
B
A
= +25°C ±5°C,
SHEET
5962-97598
20