AFCT-5715PZ-JU1 Avago Technologies US Inc., AFCT-5715PZ-JU1 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
AFCT-5715PZ-JU1
Manufacturer Part Number
AFCT-5715PZ-JU1
Description
Manufacturer
Avago Technologies US Inc.
Datasheet
1.AFCT-5715PZ-JU1.pdf
(19 pages)
Specifications of AFCT-5715PZ-JU1
Optical Fiber Type
TX/RX
Data Transfer Rate
1250MBd
Optical Rise Time
0.26/0.4ns
Optical Fall Time
0.26/0.4ns
Jitter
0.227/0.267ns
Operating Temperature Classification
Commercial
Peak Wavelength
1355nm
Package Type
SFP
Operating Supply Voltage (min)
3.14V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.47V
Operating Temp Range
-10C to 85C
Mounting
Snap Fit To Panel
Pin Count
20
Lead Free Status / RoHS Status
Compliant
Table 2. Pin description
Notes:
1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7K: – 10 K: resistor on the host board to a supply
2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 K: resistor.
3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 K: resistor on the host board to a supply less
4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 K: – 10 K: resistor on the host board
5. RD-/+: These are the differential receiver outputs. They are AC coupled 100 : differential lines which should be terminated with 100 :
6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 – 3.465 V at the SFP connector pin. The in-rush
7. TD-/+: These are the differential transmitter inputs. They are AC coupled differential lines with 100 : differential termination inside the
7
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the
output will be pulled to < 0.8 V.
than VccT +0.3 V or VccR+0.3 V.
to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined
by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
differential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on
these lines must be between 370 and 2000 mV differential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv
differential.
current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.
module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of
500 – 2400 mV (250 – 1200 mV single ended). However, the applicable recommended differential voltage swing is found in Table 5.
Name
VeeT
TX Fault
TX Disable
MOD-DEF2
MOD-DEF1
MOD-DEF0
Rate Selection
LOS
VeeR
VeeR
VeeR
RD-
RD+
VeeR
VccR
VccT
VeeT
TD+
TD-
VeeT
Low (0 – 0.8 V): Transmitter on
Between (0.8 V and 2.0 V): Undefined
High (2.0 – 3.465 V): Transmitter Disabled
Open: Transmitter Disabled
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is clock line of two wire serial interface for optional serial ID
Mod-Def 2 is data line of two wire serial interface for optional serial ID
Function/Description
Transmitter Ground
Transmitter Fault Indication
Transmitter Disable - Module disables on high or open
Module Definition 2 - Two wire serial ID interface
Module Definition 1 - Two wire serial ID interface
Module Definition 0 - Grounded in module
Not Connected
Loss of Signal
Receiver Ground
Receiver Ground
Receiver Ground
Inverse Received Data Out
Received Data Out
Reciver Ground
Receiver Power -3.3 V ±5%
Transmitter Power -3.3 V ±5%
Transmitter Ground
Transmitter Data In
Inverse Transmitter Data In
Transmitter Ground
Engagement
Order(insertion)
1
3
3
3
3
3
3
3
1
1
1
3
3
1
2
2
1
3
3
1
Notes
1
2
3
3
3
4
5
5
6
6
7
7