GFD3500-002-BBA Honeywell, GFD3500-002-BBA Datasheet - Page 2

• Manufacturer Part Number: GFD3500-002-BBA
• Description: Fiber Optic Transmitters, Receivers, Transceivers FIBER OPTIC PRODUCTS
• Manufacturer: Honeywell

Specifications of GFD3500-002-BBA

• Optical Fiber Type: RX
• Data Transfer Rate: 16Mbps
• Optical Rise Time: 10ns
• Optical Fall Time: 10ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 660nm
• Package Type: ST
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Mounting: Screw
• Pin Count: 4
• Lead Free Status / RoHS Status: Compliant

Fiber Optic Components
High-speed TTL Receiver
OPERATION
active area of the photodiode and is converted to an
electrical signal. The current is then converted to a
voltage in the transimpedance pre-amplifier. The
controlled gain limits the light current created by the
photodiode in both the transimpedance pre-amplifier
and in the post-amplifier. This avoids a possible
overcharge of the amplifier and assures optimum
PWD performance.
the system’s sensitivity limit. A final buffer provides a
TTL output. The level sensitive behavior makes the
system robust with respect to the external
interference (e.g. current/voltage spikes). The
regulator supplies the entire system to ensure high
rejection of power supply noise.
ABSOLUTE MAXIMUM RATINGS (25 ºC [77 ºF] free
air temperature unless otherwise noted.)
RECOMMENDED OPERATING CONDITIONS
TABLE 1: ELECTRO-OPTICAL CHARACTERISTICS (T
2 Honeywell • Sensing and Control
Storage
temperature
Lead solder
temperature
Supply voltage
Junction
temperature
Operating
Temperature
Supply voltage
Optical input
power
Parameter
Data rate
Cu
660 nm
Max. received power/optical level LOW
Max. received power/optical level HIGH
Input required for transition from HIGH to LOW
Output voltage high
Output voltage low
Rise time
Fall time
Pulse width distortion
Dynamic range
Bit error rate
Optical power (photons) from the fiber strikes the
The signal is compared with a threshold defining
rrent consumption
-40 ºC to 100 ºC [-40 ºF to 212 ºF]
10 s at 260 ºC [500 ºF]
6 V
150 ºC [302 ºF]
0 ºC to 70 ºC [32 ºF to 158 ºF]
4.75 V to 5.25 V
-20 dBm to -5 dBm
cycle, P
I
I
OH
OL
f = 8 MHz, 50 % duty
10 % - 90 % 2.5 kΩ,
10 % - 90 % 2.5 kΩ,
-5 dBm (average)
= 2 mA@20 pf load
= 2 mA@20 pf load
Test Condition
1 mm/POF
1 mm/POF
1 mm/POF
oIN
10 pF
10 pF
= -20 dBm to
–
–
–
–
FIGURE 1: SPECTRAL SENSITIVITY
C
NOTICE
• Stresses greater than those listed under “Absolute
• This is a stress rating only and functional
• Exposure to absolute maximum rating conditions
Failure to comply with these instructions could
result in death or serious injury.
= 25 ºC [77 ºF], V
Maximum Ratings” may cause permanent damage
to the device.
operation of the device at these or any other
conditions above those indicated in the
operational section of this specification is not
implied.
for extended periods of time may affect reliability.
A/W
0.5
0.4
0.3
0.2
0.1
0
300 400
Symbol
GFD3500-002 Series
V
PWD
P
P
P
V
BER
500
Icc
RmaxL
RmaxL
OHIGH
RminH
OLOW
–
–
t
t
r
f
CC
600 700
= 5 V unless noted)
n+/p-sub
Min.
-20
2.4
15
dc
(nm)
–
–
–
–
–
–
–
–
800
Typical
900 10001100
–
–
–
–
–
–
–
6
8
–
–
–
Max.
<10-9
±22
-31
0.4
16
45
10
10
-5
–
–
–
1200
Mbps
Unit
dBm
dBm
dBm
mA
dB
ns
ns
ns
V
V
–