AT88SC3216C-SI Atmel, AT88SC3216C-SI Datasheet
AT88SC3216C-SI
Specifications of AT88SC3216C-SI
Related parts for AT88SC3216C-SI
AT88SC3216C-SI Summary of contents
Page 1
... SOIC, PDIP 1 8 VCC NC VCC SCL SCL 4 5 GND SDA SDA CryptoMemory 32 Kbit AT88SC3216C Summary 8-lead SAP GND Bottom view Note: This is a summary document. A complete document is available under NDA. For more information, please contact your local Atmel sales office. ...
Page 2
... Up to four unique key sets may be used for these opera- tions. The AT88SC3216C offers the ability to communicate with virtually any smart card reader using the asynchronous protocol (Gemplus Patent) defined in ISO 7816-3. ...
Page 3
... The AT88SC3216C provides an ISO 7816-3 compliant asynchronous answer to reset sequence. When the reset sequence is activated, the device will output the data pro- grammed into the 64-bit answer-to-reset register. An internal pull-up on the RST input pad allows the device to be used in synchronous mode without bonding RST ...
Page 4
... Configuration Zone Security Fuses AT88SC3216C 4 The configuration zone consists of 2048 bits of EEPROM memory used for storing pass- words, keys and codes and defining security levels to be used for each user zone. Access rights to the configuration zone are defined in the control logic and may not be altered by the user ...
Page 5
... Asynchronous Protocol Synchronous 2-wire Serial Interface 5014DS–SMEM–7/04 The AT88SC3216C supports two different communication protocols. • Smart Card Applications: The asynchronous protocol defined by ISO 7816-3 is used for compatibility with the industry’s standard smart card readers. • Embedded Applications: A 2-wire serial interface is used for fast and efficient communication with logic or controllers ...
Page 6
... AT88SC3216C 6 Communications between the device and host operate in three basic modes. Standard mode is the default mode for the device after power-up. Authentication mode is acti- vated by a successful authentication sequence. Encryption mode is activated by a successful encryption activation following a successful authentication. ...
Page 7
... Checksum (CS) VERIFY CS Write DATA The AT88SC3216C implements a data validity check function in the form of a check- sum, which may function in standard, authentication or encryption modes. In the standard mode, the checksum is implemented as a Modification Detection Code (MDC), in which the host may read a MDC from the device in order to verify that the data sent was received correctly ...
Page 8
... CryptoMemory using sim- ple write and read commands. To gain access to the configuration zone, the secure code must first be successfully presented. For the AT88SC3216C device, the secure code is $CB 28 50. After writing and verfiying data in the configuration zone, the security fuses must be blown to lock this information in the device ...
Page 9
... Ordering Information Ordering Code Package AT88SC3216C-MJ M2 – J Module AT88SC3216C-MB M2 – B Module AT88SC3216C-PI 8P3 AT88SC3216C-SI 8S1 AT88SC3216C-Y4I 8Y4 AT88SC3216C-PU 8P3 AT88SC3216C-SU 8S1 AT88SC3216C-Y4U 8Y4 AT88SC3216C-WI 7 mil wafer (1) Package Type M2 – J Module M2 – B Module 8P3 8S1 8Y4 Note: 1. Formal drawings may be obtained from an Atmel sales office. ...
Page 10
... The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4 mm greater in both directions (i.e., a punched M2 module will yield 13.0 x 11.8 mm). AT88SC3216C 10 Ordering Code: MB ∅ ...
Page 11
... These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 5014DS–SMEM–7/ Top View TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT88SC3216C End View COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 1.35 – 1.75 A1 0.10 – ...
Page 12
... D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT88SC3216C ...
Page 13
... SYMBOL MIN A – A1 0.00 D 5.80 E 4.70 D1 2.85 E1 2. 0.50 TITLE 8Y4, 8-lead (6.00 x 4.90 mm Body) SOIC Array Package (SAP) Y4 AT88SC3216C MAX NOM NOTE – 0.90 – 0.05 6.00 6.20 4.90 5.10 3.00 3.15 3.00 3.15 0.40 0.45 1.27 TYP 3.81 REF ...
Page 14
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...