5962-8751502JA E2V, 5962-8751502JA Datasheet - Page 10

• Manufacturer Part Number: 5962-8751502JA
• Manufacturer: E2V

Specifications of 5962-8751502JA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
4.3.1 Group A inspection.
Margin test method B.
DEFENSE SUPPLY CENTER COLUMBUS
c.
d.
a. Tests shall be as specified in table II herein.
b. Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
(10)
(11)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(1)
(2)
(3)
(4)
(4a) Steps 1 through 4 may be performed at the wafer level. The maximum storage temperature shall not exceed
(5)
(6)
(7)
(8)
(9)
All devices selected for testing shall be programmed with a checkerboard pattern or equivalent. After completion of all
testing, the devices shall be erased and verified except devices being submitted to groups B, C, and D testing.
As a minimum, subgroups 7 and 8 shall consist of verifying the EPROM pattern specified.
COLUMBUS, OHIO 43218-3990
MICROCIRCUIT DRAWING
Bake, unbiased, for 72 hours at +140°C or for 48 hours at +150°C or for 8 hours at +200°C or 48 hours at 225°C
(unassembled devices only).
At +25°C, perform a margin test using V
Perform dynamic burn-in in accordance with 4.2a.
At +25°C, perform a margin test using V
Perform electrical test in accordance with 4.2b.
Erase in accordance with 3.6.1. Devices may be submitted to quality conformance inspection.
Verify erasure in accordance with 3.6.3.
Program at +25°C greater than 95 percent of the bit locations, including the slowest programming cell. The
remaining cells shall provide a worst case speed pattern.
Bake, unbiased, for 72 hours at +140°C or for 48 hours at +150°C or for 8 hours at +200°C or for 2 hours at
+300°C for unassembled devices only.
Perform margin test using V
Erase (see 3.6.1).
+200°C for packaged devices or +300°C for unassembled devices.
Program at +25°C with a 50 percent pattern (checkerboard or equivalent).
Perform margin test using V
Perform dynamic burn-in in accordance with 4.2a.
Perform margin test using V
Perform electrical tests (see 4.2b).
Erase (see 3.6.1), except devices submitted for groups A, B, C, and D testing.
Verify erasure (see 3.6.3).
STANDARD
m
m
m
= +5.55 V and V
= +5.75 V and V
= +5.55 V and V
m
m
= +5.8 V to loose timing (i.e., t
= +5.8 V.
m
m
m
= +4.40 V at +25°C using loose timing (i.e., t
= +4.40 V at +25°C with loose timing.
= +4.40 V at +25°C using loose timing.
SIZE
A
REVISION LEVEL
ACC
= 1 µs).
B
ACC
SHEET
= 1 µs).
5962-87515
10