AT27LV010A-70VU Atmel, AT27LV010A-70VU Datasheet
AT27LV010A-70VU
Specifications of AT27LV010A-70VU
Related parts for AT27LV010A-70VU
AT27LV010A-70VU Summary of contents
Page 1
... At V accessed in less than 90 ns. With a typical power dissipation of only MHz and V = 3.3V, the AT27LV010A consumes less than one fifth the power of a stand- CC ard 5V EPROM. Standby mode supply current is typically less than 3.3V. ...
Page 2
... Description (Continued) The AT27LV010A is available in industry standard JEDEC-approved one-time programmable (OTP) plastic PLCC and TSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. The AT27LV010A operating with V TTL level outputs that are compatible with standard TTL logic devices operating ...
Page 3
... Two identifier bytes may be selected. All Ai inputs are held V 5.5V. low (V CC gled low (V and high (V AT27LV010A Supply Voltage with 1. Minimum voltage is -0.6V dc which may undershoot to - 2.0V for pulses of less than 20 ns. Maximum output pin voltage 0.75V dc which may be ex- CC ceeded if certain precautions are observed (consult application notes) and which may overshoot to +7 ...
Page 4
... Input High Voltage IH V Output Low Voltage OL V Output High Voltage OH Notes must be applied simultaneously with or before and removed simultaneously with or after V PP AT27LV010A 3-98 AT27LV010A -90 -12 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 3.0V to 3.6V 3.0V to 3.6V 5V 10% 5V 10% Condition ...
Page 5
... CC Condition (1) 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven after the falling after the address OE . AT27LV010A AT27LV010A -90 -12 -15 Min Max Min Max Min 90 120 90 120 Units Max 150 ...
Page 6
... Input Test Waveform and Measurement Level < (10 Pin Capacitance ( MHz 25°C) Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27LV010A 3-100 (1) Max Units Output Test Load Note 100 pF including jig capacitance. Conditions ...
Page 7
... Output Low Voltage OL V Output High Voltage Supply Current (Program and Verify) CC2 Supply Current PP2 Product Identification Voltage ID (1) and 3. When programming the AT27LV010A a 0.1 F capacitor IL is required across V voltage transients. = 13.0 0.25V Test Conditions 2 -400 PGM = V AT27LV010A and ground to suppress spurious ...
Page 8
... Device Type Note: 1. The AT27LV010A has the same Product Identification Code as the AT27C010. Both are programming compatible. AT27LV010A 3-102 Rapid Programming Algorithm = 13.0 0.2V A 100 s PGM pulse width is used to program. The ad- dress is set to the first location raised to 13.0V. Each address is first programmed ...
Page 9
... Lead, Plastic J-Leaded Chip Carrier (PLCC) 32T 32 Lead, Plastic Thin Small Outline Package (TSOP) Ordering Code AT27LV010A-90JC AT27LV010A-90TC AT27LV010A-90JI AT27LV010A-90TI AT27LV010A-12JC AT27LV010A-12TC AT27LV010A-12JI AT27LV010A-12TI AT27LV010A-15JC AT27LV010A-15TC AT27LV010A-15JI AT27LV010A-15TI Package Type AT27LV010A Package Operation Range 32J Commercial 32T (0°C to 70°C) 32J Industrial 32T (-40° ...