AD53500JRPZ Analog Devices Inc, AD53500JRPZ Datasheet - Page 3

• Manufacturer Part Number: AD53500JRPZ
• Manufacturer: Analog Devices Inc

Specifications of AD53500JRPZ

• Mounting: Surface Mount
• Pin Count: 20
• Lead Free Status / RoHS Status: Compliant

NOTES
1
2
3
4
ABSOLUTE MAXIMUM RATINGS
Power Supply Voltage
Inputs
Outputs
Environmental
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD53500 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. 0
Parameter
DYNAMIC PERFORMANCE, INHIBIT
POWER SUPPLIES
NOTES
Connecting or shorting the decoupling capacitors to ground will result in the destruction of the device.
Specifications subject to change without notice.
Stresses above those listed under Absolute Maximum Ratings may cause perma-
Output short circuit protection is guaranteed as long as proper heat sinking is
The V
To ensure lead coplanarity ( 0.002 inches) and solderability, handling with bare
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Absolute maximum limits apply
individually, not in combination. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
employed to ensure compliance with the operating temperature limits.
dc-current drive capability.
hands should be avoided and the device should be stored in environments at 24 C
+V
–V
+V
DATA, DATA, INH, INH . . . . . . . . . . . . . . . . +5 V, –3 V
DATA to DATA, INH to INH
V
V
V
V
V
V
THERM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +V
Operating Temperature (Junction) . . . . . . . . . . . . . .+175 C
Storage Temperature . . . . . . . . . . . . . . . . –65 C to +150 C
Lead Temperature (Soldering, 10 sec)
Delay Time, Active to Inhibit
Delay Time, Inhibit to Active
I/O Spike
Output Leakage
Output Capacitance
PSRR, Drive Mode
Total Supply Range
Positive Supply
Negative Supply
Positive Supply Current
Negative Supply Current
Total Power Dissipation
Temperature Sensor Gain Factor
5 C (75 F
H
H
OUT
OUT
LDCPL
HDCPL
S
, V
S
S
HDCPL
to V
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7 V
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +11 V
to –V
L
Short Circuit Duration to Ground . . . . . . . Indefinite
Range in Inhibit Mode . . . . . . . . . . . . . See Figure 1
to GND . . . . . . . . . . . . . . . . . . . . . . . . . +7 V, –3 V
L
and V
. . . . . . . . Do Not Connect Except for Cap to V
. . . . . . . . . Do Not Connect Except for Cap to V
S
10 F) with relative humidity not to exceed 65%.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +10 V, 0 V
LDCPL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +18 V
capacitors may be replaced by a low value resistor for higher
1
. . . . . . . . . . . . . . . . 3 V
4
. . . . . . . . . . +260 C
Min
2
2
–1.0
Typ
<200
18
35
16
+10
–6
85
88
1.37
1.0
S
, 0 V
CC
EE
2
3
3
–3–
FIGURE 1 SHOWS THE MAXIMUM ALLOWABLE LIMITS FOR V
OF V
LIMITS, AS STATED BEFORE, ARE MAXIMUM RATINGS ONLY, AND SHOULD NOT
BE USED AS THE PART'S NORMAL OPERATING RANGE. THIS RANGE APPLIES
ONLY TO SUPPLIES OF +V
PROPORTIONALLY FOR LOWER SUPPLIES.
Max
10
10
+1.0
95
98
1.54
HIGH
V
Figure 1. Absolute Maximum Ratings for V
OUT
AND V
Units
ns
ns
mV, p-p
pF
dB
V
V
V
mA
mA
W
= (MIN) = –3V
A
A/K
LOW
–2
WHEN THE DRIVER IS OPERATING IN INHIBIT MODE. THE
–1
V
OUT
S
7
6
5
4
3
2
1
= +10V AND –V
–1
–2
–3
Test Conditions
Measured at 50%, V
V
Measured at 50%, V
V
V
V
Driver Inhibited
V
R
1
L
L
H
OUT
S
LOAD
V
= V
= –2 V, 50
= –2 V, 50
OUT
= 0 V, V
2
= –2 V to +6 V
= (MAX) = +7V
S
= 10 k , V
3
V
3%
S
4
HIGH
L
WARNING!
= –6V AND SHOULD BE DERATED
= 0 V
5
/ V
Terminated to Ground
Terminated to Ground
LOW
SOURCE
6
H
H
= +2 V,
= +2 V,
ESD SENSITIVE DEVICE
= +10 V
OUT
AS A FUNCTION
AD53500
V
H
OUT
, V
L