D4N-1131 Omron, D4N-1131 Datasheet - Page 21

• Manufacturer Part Number: D4N-1131
• Description: Pf13.5/1NC/1NO, Top Plng.
• Manufacturer: Omron

Specifications of D4N-1131

• Operating Force Max: 6.5N
• Contact Voltage Ac Max: 240V
• Contact Voltage Dc Max: 250V
• Contact Current Ac Max: 10A
• Contact Current Dc Max: 2.5A
• Switch Terminals: Screw
• Svhc: No SVHC (15-Dec-2010)
• Actuator: RoHS Compliant
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

• Use a cable with a suitable diameter for the connector.
• Attach and tighten a conduit cap to the unused conduit opening
Changing the Lever
The lever mounting screws can be used to set the lever position to
any position in a 360° angle at 7.5° increments. Grooves are incised
on the lever and rotary shaft that engage to prevent the lever from
slipping against the rotary shaft. The screws on adjustable roller
lever models can also loosened to change the length of the lever.
Remove the screws from the front of the lever before mounting the
lever in reverse (front/back), and set the level so that operation will be
completed before exceeding a range of 180° on the horizontal.
Recommended Connectors
Use connectors with screws not exceeding 9 mm, otherwise the
screws will protrude into the case interior, interfering with other
components in the case. The connectors listed in the following table
have connectors with thread sections not exceeding 9 mm. Use the
recommended connectors to ensure conformance to IP67.
Production Termination
Following the release of the D4N, production of the D4D-N will be ter-
minated.
Date of Production Termination
Production of the D4D-N Series will be terminated in March 2006.
Product Replacement
1. Dimensions
2. Terminal Numbers
3. Recommended Terminals
G1/2
Pg13.5
M20
1/2-14NPT
M12
when wiring. Tighten the conduit cap to the specified torque. The
conduit cap is provided with the Switch (2-conduit types).
The D4D-N and D4N use the same mounting method, and
mounting hole. The multi-contact structure and the extra 4 mm in
length, however, are different.
For the 2-contact slow-action model, the terminals 21, 22, 23, and
24 on the D4D-N are 31, 32, 33, and 34 on the D4N.
If the recommended terminals are not used, the Switch may not
be compatible. Make sure that the Switch is compatible with the
terminals.
Size
LAPP
Ohm Denki
LAPP
LAPP
LAPP
LAPP
Manufacturer
ST-PF1/2
5380-1002
OA-W1609
OA-W1611
ST-13.5
5301-5030
ST-M20 × 1.5
5311-1020
ST-NPT1/2
5301-6030
ST-M12 × 1.5
5311-1000
Model
6.0 to 12.0 mm
7.0 to 9.0 mm
9.0 to 11.0 mm
6.0 to 12.0 mm
7.0 to 13.0 mm
6.0 to 12.0 mm
3.5 to 7.0 mm
Applicable cable
diameter
Use LAPP connectors together with seal packing (JPK-16, GP-13.5,
GPM20, or GPM12), and tighten to the specified tightening torque.
Seal packing is sold separately.
LAPP is a German manufacturer. Ohm Denki is a Japanese
manufacturer.
Before using an M12 type, attaching the provided changing adaptor
to the Switch and then connect the recommended connector.
Before using a 2-conduit 1/2-14NPT type, attach the provided
changing adaptor to the Switch and then connect the recommended
connector.
Storage
Do not store the Switch in locations where hazardous gases (e.g.,
H
to high temperatures and humidity.
Others
• Do not allow the load current to exceed the rated value.
• Confirm that the seal rubber has no defects before use.
• Use the correct cover mounting screws only, or the sealing
• Inspect the Switch regularly.
• Make sure that foreign particles do not enter the head when
• Use the following recommended countermeasures to prevent
1. Make the rear edge of the dog smooth with an angle of 15° to 30°
2. Design the circuit so that no error signal will be generated.
3. Use or set a Switch that is operated in one direction only.
Comparison of the D4D-N and Substitute
Products
Model
Switch color
Dimensions
Wiring/connection
Mounting method
Ratings/performance
Operating characteristics
Operating method
2
If the seal rubber is displaced or raised, or has foreign particles
adhered to it, the sealing capability of the seal rubber will be
adversely affected.
capability of the seal rubber will deteriorate.
removing the screws from the four corners to change the head
position in any of the four directions.
telegraphing when using adjustable or long levers.
S, SO
or make it in the shape of a quadratic curve.
2
Miniature Safety Limit Switch
, NH
3
, HNO
3
, Cl
2
) or dust is present, or in locations subject
Very similar
Completely compatible
D4N
Very similar
Very similar
Significantly different
Completely compatible
Very similar
D4N
21