05113861634 3M Interconnect Solutions, 05113861634 Datasheet - Page 3

• Manufacturer Part Number: 05113861634
• Description: Conn Ejector Header HDR 26 POS 2.54mm Solder ST Thru-Hole
• Manufacturer: 3M Interconnect Solutions
• Type: Ejector Headerr

Specifications of 05113861634

• Pitch: 2.54 mm
• Number Of Rows: 2
• Number Of Contacts: 26
• Gender: HDR
• Contact Plating: Gold Over Nickel
• Termination Method: Solder

.100” × .100” Latch/Ejector, Straight and Right Angle
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
Ordering Information
* Available without center notch B. Contact 3M.
Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518).
N = High Temp Black (PCT)/(RB Plating Req’d)
Blank = Std. Temp Gray (PBT) /(Blank or UB Pltg. Req’d.)
Pin Qty
Number Suffix
06
08
10
14
16
20
24
26
30
34
40
50
60
64
2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (3M
3M Part
3. The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 ± .002. See page 4 for kink position details (K2 version).
4. Contact your 3M sales representative for custom requirements.
-5XX2
-6XX2
-5X03
-6X03
Part # 3341-6) with .106 [2.69] dia mounting hole may be used.
™
Number
3M Part
3869
3889
3793
3314
3408
3428
3627
3429
3440
3431
3432
3433
3372
3764
(2.39) to .125 (3.18)
Solder Tail for 0.94
Thick PC Board
Thick PC Board
“Y”
Contact Tail
Solder Tail for
.062 (1.57)
3.965 (100.71)
3M Part Number
1.065 (27.05)
1.165 (29.59)
1.265 (32.13)
1.465 (37.21)
1.565 (39.75)
1.765 (44.83)
1.965 (49.91)
2.065 (52.45)
2.265 (57.53)
2.465 (62.61)
2.765 (70.23)
3.765 (95.63)
3.265 (82.93)
.100 ± .003
[2.54]
[1.52]
(See Table 1)
.060
C L
A
Recommended Mounting Hole Pattern
.300
[7.62]
Side to Side Stackability
5 = Right Angle Solder Tails
.112 ± .010
.155 ± .010
6 = Straight Solder Tails
Dim E
(2.84)
(3.94)
0.905 (22.99)
1.005 (25.53)
1.105 (28.04)
1.305 (33.12)
1.405 (35.66)
1.605 (40.74)
1.805 (45.82)
1.905 (48.36)
2.105 (53.44)
2.305 (58.52)
2.605 (66.14)
3.105 (78.84)
3.605 (91.54)
3.805 (96.62)
Pin Configuration
B
Table 1
Dimensions
Position 1
.0245 ± .0005
.0245 ± .0005
ø.106
(Straight)
[2.69]
Table 2
.100 ± .003
[2.54]
(0.622)
(0.622)
Dim F
(See Note 2)
[8.94]
.352
B
Dim G
0.665 (16.89)
0.765 (19.43)
0.865 (21.97)
or
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
X3XXX-XXXXXX
Pin Cross Section
ø.116
Latch/Ejector System
0 = No Latch/Ejector installed
2 = Short Roll Pin Latch/Ejectors
3 = Long Roll Pin Latch/Ejectors
5 = Short, Snap-In Latch/Ejectors
6 = Long, Snap-In Latch/Ejectors
[2.95]
C
.028 ± .001
.028 ± .001
Diagonals
(0.71)
(0.71)
0.505 (12.83)
0.605 (15.37)
0.705 (17.91)
0.905 (22.99)
1.005 (25.53)
1.205 (30.61)
1.405 (35.69)
1.505 (38.23)
1.705 (43.31)
1.905 (48.39)
2.205 (56.01)
2.705 (68.71)
3.205 (81.41)
3.405 (86.49)
Corner Radii
.0075 Ref
.0075 Ref
D
(0.191)
(0.191)
Polarizing
Notches
"Y"
For technical, sales or ordering information call
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
BC
BC
(0.89) (See Note 3)
Tail
02 = for .062 [1.57] thick board
03 = for .094 to .125 [2.39 to 3.18] thick board
K2 = kinked for .062 [1.57] thick board
0.035 ± .003 (0.89)
B*
B*
.100 ± .003
[2.54]
0.035 ± .003
Plating
RB = 30 μ” [ 0.76 μm ] Gold and 200 μ” [ 5.08 μm ] Matte Tin
(App. E1 & C1 Apply)
Blank or UB = 30 μ” (0.76 μm ] Gold and 200 μ” [ 5.08 μm ]
Tin Lead (App. E3 & C2 Apply)
C L
[0.74]
Dim G
.029
Recommended Mounting Hole Pattern
.41
[10.4]
Max to Edge of PCB
for Daisy Chain
3M is a trademark of 3M Company.
Inch
Tolerance Unless Noted
(Right Angle)
(See Note 2)
.100 ± .003
[2.54]
Position 1
[ ] Dimensions for
Reference only
ø.106
± .1
[2.69]
.0
[5.89]
.232
C
(mm)
Inch
Dim G
or ø.116
± .01
.00
3000 Series
[2.95]
800-225-5373
± .005
.000
Sheet 3 of 4
TS-0772-L