LX5252CDB MICROSEMI, LX5252CDB Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/443/microsemi_sml.jpg)
LX5252CDB
Manufacturer Part Number
LX5252CDB
Description
Manufacturer
MICROSEMI
Type
SCSI Terminationr
Datasheet
1.LX5252CDB.pdf
(8 pages)
Specifications of LX5252CDB
Number Of Bits
9
Operating Supply Voltage (typ)
3.3/5V
Operating Supply Voltage (max)
5.25V
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Compliant
Copyright © 2002
Rev. 1.2b, 2005-08-29
1+, 2+, 3+, 4+, 5+, 6+, 7+, 8+, 9+
1-, 2-, 3-, 4-, 5-, 6-, 7-, 8-, 9-
TM
MASTER/SLAVE
DISCONNECT
DIFFSENSE
P
HEATSINK
IN
DIFFB
V
GND
HVD
LVD
SE
N
TERM
AME
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Negative signal termination lines for LVD mode. Signal termination lines for SE mode.
Positive signal termination lines for LVD mode. Psuedo-ground lines for SE mode.
Power supply pin for terminator. Connect to SCSI bus VTERM. Must be
decoupled by one 4.7
absolutely necessary to connect this pin to the decoupling capacitor through a very low
impedance (big traces to PCB). Keeping distances very short from the decoupling
capacitors is somewhat layout dependent and some applications may benefit from high
frequency decoupling with 0.1
Enables/Disables terminator. See Power Down Function Table for logic levels
for LX5250 and LX5252
Terminator ground pin. Connect to ground.
Sometimes referred to as M/S pin in this datasheet. Used to select which terminator is the
controlling device. M/S pin High or Open enables the DIFFSENSE output drive. Please
see MASTER/SLAVE Function Table.
This is a dual function pin. It drives the SCSI bus DIFFSENS line. It is also the sense pin
to detect the SCSI bus mode (LVD, SE, or HVD). DIFFSENSE output drive can be
disabled with low level on the M/S pin. Please see DIFFSENSE and MASTER/SLAVE
Function Tables. Internally connected to DIFFB pin through a 20K
Internally connected to DIFFSENSE pin through a 20K
mode sense pin when the device is non-controlling terminator (M/S is low). An RC filter
(50K
Single-Ended output; when High, terminator is operating in SE mode.
Low Voltage Differential output; when High, terminator is operating in LVD mode.
High Voltage Differential output; when High, terminator is operating in HVD mode.
Attached to die mounting pad, but not bonded to GND pin. Pins should be considered a
heat sink only, and not a true ground connection. It is recommended that these pins be
connected to ground, but can be left floating.
F U N C T I O N A L P I N D E S C R I P T I O N
Ω
resistor &
Integrated Products Division
®
Microsemi
4.7
µ
F) is not required on the LX5250 as it has an internal timer.
µ
F low-ESR capacitor for every three terminator devices. It is
.
µ
9-Line Multimode SCSI Terminator
F capacitors at V
D
ESCRIPTION
P
RODUCTION DATA SHEET
TERM
pin.
Ω
resistor. It can be used as a
Ω
resistor.
LX5250/5252
Page 5