SCAN921226HSM National Semiconductor, SCAN921226HSM Datasheet - Page 2
![](/photos/31/33/313328/49pin_fbga_sml.jpg)
SCAN921226HSM
Manufacturer Part Number
SCAN921226HSM
Description
Manufacturer
National Semiconductor
Datasheet
1.SCAN921226HSM.pdf
(21 pages)
Specifications of SCAN921226HSM
Number Of Elements
1
Input Type
CMOS/TTL
Operating Supply Voltage (typ)
3.3V
Differential Input High Threshold Voltage
50mV
Diff. Input Low Threshold Volt
-50mV
Output Type
Deserializer
Transmission Data Rate
800Mbps
Power Dissipation
1.47W
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
49
Number Of Receivers
1
Number Of Drivers
10
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SCAN921226HSM/NOPB
Manufacturer:
NSC
Quantity:
964
Company:
Part Number:
SCAN921226HSMX
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
SCAN921226HSMX/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
www.national.com
Block Diagrams
Functional Description
The SCAN921025H and SCAN921226H are a 10-bit Serial-
izer and Deserializer chipset designed to transmit data over
differential backplanes at clock speeds from 20 to 80 MHz.
The chipset is also capable of driving data over Unshielded
Twisted Pair (UTP) cable.
The chipset has three active states of operation: Initializa-
tion, Data Transfer, and Resynchronization; and two passive
states: Powerdown and TRI-STATE. In addition to the active
and passive states, there are also test modes for JTAG
access and at-speed BIST.
The following sections describe each operation and passive
state and the test modes.
Initialization
Initialization of both devices must occur before data trans-
mission begins. Initialization refers to synchronization of the
Serializer and Deserializer PLL’s to local clocks, which may
be the same or separate. Afterwards, synchronization of the
Deserializer to Serializer occurs.
Step 1: When you apply V
rializer, the respective outputs enter TRI-STATE, and on-chip
power-on circuitry disables internal circuitry. When V
reaches V
ing to a local clock. For the Serializer, the local clock is the
transmit clock (TCLK) provided by the source ASIC or other
device. For the Deserializer, you must apply a local clock to
the REFCLK pin.
The Serializer outputs remain in TRI-STATE while the PLL
locks to the TCLK. After locking to TCLK, the Serializer is
now ready to send data or SYNC patterns, depending on the
levels of the SYNC1 and SYNC2 inputs or a data stream.
The SYNC pattern sent by the Serializer consists of six ones
and six zeros switching at the input clock rate.
Note that the Deserializer LOCK output will remain high
while its PLL locks to the incoming data or to SYNC patterns
on the input.
Step 2: The Deserializer PLL must synchronize to the Seri-
alizer to complete initialization. The Deserializer will lock to
CC
OK (2.5V) the PLL in each device begins lock-
CC
to both Serializer and/or Dese-
(Continued)
CC
Application
2
non-repetitive data patterns. However, the transmission of
SYNC patterns enables the Deserializer to lock to the Seri-
alizer signal within a specified time. See Figure 16.
The user’s application determines control of the SYNC1 and
SYNC 2 pins. One recommendation is a direct feedback loop
from the LOCK pin. Under all circumstances, the Serializer
stops sending SYNC patterns after both SYNC inputs return
low.
When the Deserializer detects edge transitions at the Bus
LVDS input, it will attempt to lock to the embedded clock
information. When the Deserializer locks to the Bus LVDS
clock, the LOCK output will go low. When LOCK is low, the
Deserializer outputs represent incoming Bus LVDS data.
Data Transfer
After initialization, the Serializer will accept data from inputs
DIN0–DIN9. The Serializer uses the TCLK input to latch
incoming Data. The TCLK_R/F pin selects which edge the
Serializer uses to strobe incoming data. TCLK_R/F high
selects the rising edge for clocking data and low selects the
falling edge. If either of the SYNC inputs is high for 5*TCLK
cycles, the data at DIN0-DIN9 is ignored regardless of clock
edge.
After determining which clock edge to use, a start and stop
bit, appended internally, frame the data bits in the register.
The start bit is always high and the stop bit is always low.
The start and stop bits function as the embedded clock bits
in the serial stream.
The Serializer transmits serialized data and clock bits (10+2
bits) from the serial data output (DO
frequency. For example, if TCLK is 80 MHz, the serial rate is
80 x 12 = 960 Mega-bits-per-second. Since only 10 bits are
from input data, the serial “payload” rate is 10 times the
TCLK frequency. For instance, if TCLK = 80 MHz, the pay-
load data rate is 80 x 10 = 800 Mbps. The data source
provides TCLK and must be in the range of 20 MHz to 80
MHz nominal.
The Serializer outputs (DO
nection or in limited multi-point or multi-drop backplanes.
The outputs transmit data when the enable pin (DEN) is
±
) can drive a point-to-point con-
±
) at 12 times the TCLK
20120702