MC34910BAC Freescale, MC34910BAC Datasheet - Page 66

no-image

MC34910BAC

Manufacturer Part Number
MC34910BAC
Description
Manufacturer
Freescale
Datasheet

Specifications of MC34910BAC

Turn Off Delay Time
10us
Number Of Drivers
2
Operating Temperature (min)
-40C
Lead Free Status / RoHS Status
Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC34910BAC
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC34910BACR2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
integrated and cost-effective solution for automotive and
industrial applications. For automotive body electronics, the
33910 is well suited to perform keypad applications via the
LIN bus.
as high side outputs. Other ports are also provided, which
graphic representation of the various pins referred to in the
following paragraphs. Also, see the
for a description of the pin locations in the package.
RECEIVER OUTPUT (RXD)
the LIN interface and reports the state of the bus voltage:
RXD low when LIN bus is dominant, RXD high when LIN bus
is recessive.
TRANSMITTER INPUT (TXD)
the LIN interface and controls the state of the bus output
(dominant when TXD is Low, recessive when TXD is High).
case the input is left floating.
LIN BUS (LIN)
receiver. It is suited for automotive bus systems and is
compliant to the LIN bus specification 2.0.
Request modes.
SERIAL DATA CLOCK (SCLK)
changes on the negative transition of the SCLK. MOSI is
sampled on the positive edge of the SCLK.
MASTER OUT SLAVE IN (MOSI)
data input is sampled on the positive edge of SCLK.
MASTER IN SLAVE OUT (MISO)
digital tri-state output used to shift serial data to the
Analog Integrated Circuit Device Data
Freescale Semiconductor
The 33910 is designed and developed as a highly
Two power switches are provided on the device configured
See
The RXD pin is a digital output. It is the receiver output of
The TXD pin is a digital input. It is the transmitter input of
This pin has an internal pull-up to force recessive state in
The LIN pin represents the single-wire bus transmitter and
The LIN interface is only active during Normal and Normal
The SCLK pin is the SPI clock input pin. MISO data
The MOSI digital pin receives SPI data from the MCU. This
The MISO pin sends data to an SPI-enabled MCU. It is a
Table 1, 33910 Simplified Application
33910 Pin Connections
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
Diagram, for a
INTRODUCTION
include a wake-up capable pin amd a Hall Sensor port
supply. An internal voltage regulator provides power to a
MCU device.
communicates using a single wire. This enables this device
to be compatible with 3-wire bus systems, where one wire is
used for communication, one for battery, and one for ground.
microcontroller. Data on this output pin changes on the
negative edge of the SCLK. When CS is High, this pin will
remain in high-impedance state.
CHIP SELECT (CS)
valid SPI communication and allow for several devices to be
connected in the same SPI bus without contention. A rising
edge on CS signals the end of the transmission and the
moment the data shifted in is latched. A valid transmission
must consist of 8 bits only.
pin will generate a wake-up condition for the 33910.
ANALOG MULTIPLEXER (ADOUT0)
the MCU A/D converter to read the several inputs of the
Analog Multiplexer, including the L1 input voltage and the
internal junction temperature.
PWM INPUT CONTROL (PWMIN)
Request and Normal mode.
operation to the high side control register (HSCR).
RESET (RST)
33910 detects a reset condition or to inform the 33910 that
the MCU has just been reset. After release of the RST pin
Normal Request mode is entered.
formed by a weak pull-up and a switchable pull-down
structure which allows this pin to be shorted either to V
to GND during software development without the risk of
destroying the driver.
Also included in this device is a LIN physical layer, which
CS is a active low digital input. It must remain low during a
While in STOP mode a low-to-high level transition on this
The ADOUT0 pin can be configured via the SPI to allow
This digital input can control the high sides in Normal
To enable PWM control, the MCU must perform a write
This pin has an internal 20 μA current pull-up.
This bidirectional pin is used to reset the MCU in case the
The RST pin is an active low filtered input and output
FUNCTIONAL DESCRIPTION
INTRODUCTION
DD
33910
or
66

Related parts for MC34910BAC