MC33911G5ACR2 Freescale, MC33911G5ACR2 Datasheet - Page 25
![](/photos/31/26/312678/296-32-tqfp_sml.jpg)
MC33911G5ACR2
Manufacturer Part Number
MC33911G5ACR2
Description
Manufacturer
Freescale
Datasheet
1.MC33911G5ACR2.pdf
(92 pages)
Specifications of MC33911G5ACR2
Turn Off Delay Time
10us
Number Of Drivers
2
Operating Temperature (min)
-40C
Operating Temperature (max)
125C
Operating Temperature Classification
Automotive
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC33911G5ACR2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
RESET PIN (RST)
33911 detects a reset condition, or to inform the 33911 that
the MCU has just been reset. After release of the RST pin,
Normal Request mode is entered.
formed by a weak pull-up and a switchable pull-down
structure which allows this pin to be shorted either to V
to GND during software development, without the risk of
destroying the driver.
INTERRUPT PIN (IRQ)
faults to the MCU while in Normal and Normal Request mode
or to signal a wake-up from Stop mode. This active low output
will transition to high only after the interrupt is acknowledged
by a SPI read of the respective status bits.
WATCHDOG CONFIGURATION PIN (WDCONF)
watchdog. A resistor can be connected to this pin to configure
the window watchdog period. When connected directly to
ground, the watchdog will be disabled. When this pin is left
open, the watchdog period is fixed to its lower precision
internal default value (150 ms typical).
GROUND CONNECTION PINS (AGND, PGND,
LGND)
Power ground pins.
regulator.
return as in the relay-drivers and LIN interface pin.
together.
LOW SIDE PINS (LS1 AND LS2)
outputs are short-circuit protected and include active clamp
circuitry to drive inductive loads. Due to the energy clamp
voltage on this pin, it can raise above the battery level when
switched off. The switches are controlled through the SPI and
can be configured to respond to a signal applied to the
PWMIN input pin.
In case of VS1 disconnection and the low sides are still
Analog Integrated Circuit Device Data
Freescale Semiconductor
This bidirectional pin is used to reset the MCU in case the
The RST pin is an active low filtered input and output
The IRQ pin is a digital output used to signal events or
The WDCONF pin is the configuration pin for the internal
The AGND, PGND and LGND pins are the Analog and
The AGND pin is the ground reference of the voltage
The PGND and LGND pins are used for high current load
Note: PGND, AGND and LGND pins must be connected
LS1 and LS2 are the low side driver outputs. Those
Both low side switches are protected against overheating.
DD
or
supplied by V
VDS voltage equal to the clamping value, as stated in the
specification.
DIGITAL/ANALOG PINS (L1 AND L2)
digital inputs, which can be sampled by reading the SPI and
used for wake-up when 33911 is in low power mode or used
as analog inputs for the analog multiplexer. When used to
sense voltage outside the module, a 33 kohm series resistor
must be used on each input.
configured to operate in cyclic-sense mode. In this mode the
high side switch is configured to be periodically turned on and
sample the wake-up inputs. If a state change is detected
between two cycles a wake-up is initiated. The 33911 can
also wake-up from Stop or Sleep by a simple state change on
L1 and L2.
pins is scaled down by an selectable internal voltage divider
and can be routed to the ADOUT0 output through the analog
multiplexer.
will be disabled as a digital input and remains disabled in low
power mode. No wake-up feature is available in that
condition.
the voltage divider is disconnected from that input.
HIGH SIDE OUTPUT PIN (HS1)
or lamps. Its structure is connected to the VS2 supply pin.
The pin is short-circuit protected and also protected against
overheating.
applied to the PWMIN input pin.
for the cyclic-sense of the wake inputs.
POWER SUPPLY PINS (VS1 AND VS2)
application, VS1 and VS2 pins must be protected against
reverse battery connection and negative transient voltages
with external components. These pins sustain standard
automotive voltage conditions such as a load dump at 40 V.
other internal blocks are supplied by the VS1 pin.
The Lx pins are multi purpose inputs. They can be used as
When used as wake-up inputs L1 and L2 can be
When used as analog inputs, the voltage present on the Lx
Note: If an Lx input is selected in the analog multiplexer, it
When an Lx input is not selected in the analog multiplexer,
This high side switch is able to drive loads such as relays
HS1 is controlled by SPI and can respond to a signal
The HS1 output can also be used during low-power mode
Those are the battery level voltage supply pins. In an
The high side switch (HS1) is supplied by the VS2 pin. All
BAT
through a load, both low sides will have a
FUNCTIONAL PIN DESCRIPTION
FUNCTIONAL DESCRIPTION
33911
25